Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Is there any good documentation onCME licensing? I cant seem to find any good docs of how it works.Thanks.
I have 3 ATAs that will not even connect to the network. They came from other locations and I do not know how to get into them to change IP address, etc. The red light is flashing but I am not getting any link lights.
All,I have a scenario to which I don't have a suitable solution at the moment.We are using SNR (single number reach), but when I'm busy with my IP phone, and a second call comes in, it will extend to my mobile phone.Since I can't talk both into my IP...
Hi,Pls. help me configuring a translation rule for incomming call.Call flow: Mobile Phone (any number)---->GSM network (E1) ---> H.323 VG (E1)-->CUCM----->IP Phone (50001 - 59999).I have configured :voice translation-rule 1 rule 1 /\(.*\)/ /50001...
Hello,got CUCM 7.0(2) and CUC 7.0(2) running on two VMs. I can't upgrade either of them to any 7.1 version. I get the same error message everytime:Error encountered: errors.upgrade.systemHas anyone run into this? Has anyone successfully upgraded 7.0 ...
Hi,We have call Manager 6.1 & OCS R2 .Calls coming in to CUCM is fine, but calls made outside from the OCS is not happening. It gives the error with saying, not able to reach to gateway.Checked with the SIP trunk on CUCM, tried reseting the trunk & r...
Quick questions - We are using Cisco Media Medules in our 6500 Series Switches. The curernt version is 12.4(13d). Is it capable of supporting T.38 Fax Relay? If not, what will be feasible solution for us to migrate the RightFax with current VOIP? Tha...
Hello,which MCS would you suggest for a maximum 250 users? I think MCS-7816which MCS would you suggest for a maximunm 500 users? I think MC-7825which CUCM version would you suggest 7.0 or 7.1?also I need a minimum cost E1 gateway fully working with m...
Do we have any known issues with CUCM 7.1.3...while CFAll to any PSTN number?The setup is a migration from 4.1.3 to 7.1.3TIA..-Amit
Hi all,Now, I want to migrate my CISCO CME to the CISCO CCM 7.1. Is it possible to use the existing IP phone set license ? So, I don't need to extra license for these phone set.ThanksLeung CHe Man
Hi all.I have a problem where the fxs ports in a VG224 just disapeared.I can not configure a voice port any more. tried removing the VG224 from CUCM and adding it again doesn't work.some show commands below.Any idea to what could be the problem.Thank...
I have been browsing through the posts and found a few that talk about the originating caller ID not being displayed on calls coming in from the PSTN destined to the IP Phone and then forwarded onwards to another PSTN destination like a mobile phone....
How can I delete the default background on the 7965\7945 phones? We have uploaded a new corporate image and its the only pic in the list.xml file but the phone shows the default and the new background image. We need to remove the default so the only...
Due to rapid expansion, a customer has run out of extensions and voicemail boxes on the Primary CME (3845 CME v7) with T1 / ISDN PRI. The DID blocks (there are 4 different blocks) are connected to the 3845 router.We have setup a 2811 CME v7 (No T1 ca...
Hi all,Could you tell me what is the latest version of CISCO Unity ? Also, how many component and devices I want to buy for about 70 voice mail?ThanksLeung Che Man
