Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,This be a noddy question, but the SRND mentions the following -The Cisco Unified IP Phones 7902G, 7905G, 7910G, 7910G+SW, and 7912G are no longer availablefor sale, but they are still supported by Cisco Unified Communications Manager 7.x.It does n...
Hello all, my CEO is repeatedly receiving calls/voicemails from a number which appears to be 905323101589. No message is left nor is anything audible heard on the line when he picks up, so it seems like something is mistakenly dialing him over and o...
Hi,I have a series of IP phone 7911, when i call them, and try to answer through the soft key "answer", it says that function is not activated, can you kindly help me through that?Thanks in advance
Callmanager 4.1(3).Is there any way you can autodial numbers when connected on a call eg.Our customer calls an external IVR sytem, when the call is answered, they have to enter a 12 digit pin code.They would like to automate this.Can anyone think of ...
I'm having issues where the Call Manager server is not responding to SNMP requests even though the server claims to be up and running SNMP correctly, when I do a "utils snmp test" I get the following output. Any ideas what is happening? Any input t...
On a CallManager 6.1 I went into Cisco Unified Reporting and ran the Unified CM Device Counts Summary. The number of 7942s the report is showing is about 75 higher than what CallManager shows. I checked the database replication status in RTMT and a...
Is there a way to change 100 extensions in Unity?
I have a translation pattern xlat'ing a DID # to an external fax # with the called party transform mask set to 9xxxxxxxxxx (local # so no preceding 1 is necessary). Doubt it matters but the fax machine is in the same physical location as the gateway...
My customer need a feature called "Auto Busy Dial" that allows a station user how has placed an outside call to a busy number to have the system redial the number until the call is connected.I wonder if CME can provides this feature or not?Thanks
Hi,I entered a bad license file in CM and I was wondering how I remove it from the system even though it is not doing anything. It is not a big deal but I have seen a TAC engineer go in the CLI and do it before but do not remember the command.Thanks
hi, i am trying to make a sip trunk between a cme 7.0 and ccm 4.1, the ccm 4.1 already has a sip trunk working to an OCS, so i created a new one, but i had to change the ccm's incoming port to 5061, to create it.....!!so i want to know, how can i con...
I'm having an issue where when an office member is paging a room through the phone, the paging gets cut off when an incoming call comes in and is picked up on another phone....yet they can hear the room but the room can't hear them. This is happenin...
Hello,I've successfuly installed CM6.1.2 on new hardware (while leaving existing pub/sub intact)using dma and registered the lics. How do i start using the new server? I tried changing the ip address on one of my 7940's to point to the new server w...
Hi, I have configured the Cisco Call Manager 4.1 and the Cisco Call Manager Express 7.0 to integrate them.Configuration In the CCME:dial-peer voice 1000 voip destination-pattern <extension of the CCM> session protocol sipv2 session target ipv4:<ip ad...
Hello,On CUCM 6, when my users want to access the user page, they should type http://ipaddress/ccmuser, but in CUCM 4.1 i was redirectng just the ip address directly to this link so it was much easier for them to access the page. How can I do this in...
