Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear colleagues, new to Cisco UCM, and i am trying to change my phone language from german to english but it is not working. So far i have changed the values on three different sections: 1. Phone Configuration - User Locale 2. End User Configuratio...
Hi All, I am looking for the queries to deploy 11.5 CUCM cluster 1.How many servers we can have in one CUCM cluster ? 2.A cluster can support up to how many endpoint ? 3.A single cucm server can support up to how many endpoint ? 4.A call manager g...
Hello everyone, CUC 8.6 in play. I am finding a lot of information on resetting teh password if it has been lost but not a lot on just changing it. Anyone have a link available? Thanks in advance! All replies rated.
the phone registerd, and after 1 minute fail the provider tell me that i nead to configure the phone, to work with stun/nat... i didnt fine in the sepmac.cnf.xml the tag that i need can anyone can help me
Could anyone point me in the right direction on how to set up a cell phone for use with Call Manager 11.5 ? I followed a Cisco doc, it seems to be missing a step or made assumptions ? Could anyone offer an opinion about the usefulness of doing th...
Hello, I have read a little bit about Dynamic ePhone Hunt Group Membership, but I am not sure that this is exactly what I need. I would like to achieve two things with a hunt-group configured in a Gateway for SRST purposes. Phones will register to ...
Hi all, I'm here with another one of those issues where all of the phones will only register with the Publisher. I will try to provide as much information as possible in order not to waste anyone's time. - I have stood up a new VM server cluster ...
Hi folks, i have query on the above subject. This is considering building a new CUCM PUB/SUB on non-Cisco hardware, preferably for HP DL380G9 hardware. I have refered below document but this doesn't talk about the CUCM 11.5 or later. Is there any oth...
Is there a way in Call Manager 11.5, to, upon transferring a call, (to a cell or other phone), to some how notify or have an alternate called id to alert the user that this call is a priority and to pick up ? Thanks for any insight
I have a standard setup: CUCM <=> CUBE <=> ITSP In my CUBE's config, I have: voice service voip address-hiding dtmf-interworking rtp-nte mode border-element allow-connections sip to sip ... voice class codec 1 codec preference 1 g711alaw ... ...
Hello, We have two Cisco 2900 routers, both of them connected to Cucm. i checked from PSTN caller id is enable receiving on display & lesson String on Test hand set. Other lines on router doesn't have any caller-id problem. This voice port has same...
We are using CUCM 8.5When I upgrade firmware I see below information on Phone.Is this successfully upgraded to ver sip9971.9-2-4-19?Why do I see ver 9.1 under Phone device ? What is this download status shows Failed?I would like to know, whether this...
Hi!If I Export all Directory Number (Unassigned) the file format created by CUCM is as follow;DIRECTORY NUMBER,ROUTE PARTITION,DESCRIPTION,ALERTING NAME,ASCII ALERTING NAME,VOICE MAIL PROFILE,CALLING SEARCH SPACE,PRESENCE GROUP,USER HOLD MOH AUDIO SO...
Hi, We have a 10.5 CUCM cluster with a Pub and a Sub. We also have hardware conferences resources in a 2811 ISR. Conferences resources are registered to Subscriber, but when we make a conference with external numbers, the remote IP address shown ...
Hi, I am using 8845 with cucm 11.5 and creating hunt group on it. I also setting schedule which are bussiness hour and nonbussiness hour and apply them into the partition. Before I apply the schedule, the check box of "Logged Into Hunt Group" in 88...
