Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
How to stop isp1 routes advertisement via isp2 on Bgp... The problem is when my spoke isp1 mpls down... Still it is getting routes via isp2
Hello I´m studying for my 100.101 CCENT and was thinking... Is Static Routing Table much faster than OSPF? What would be the difference scaled to a big Network? Is it worth trying? Thank youBest regards
hi Guys, I am trying to do a "no switchport" on cisco 7609 router but it keeps rejecting the command.lab01(config-if)#no switchport Command rejected: not allowed on this interface. Interface config - sh run int te2/0/1Building configuration...Current...
Hi. Thanks viewing my post!I'm trying out some QoS configuration for a VDI deployment and have a problem with our 6509 switches not marking the traffic (possibly user error)..As VDI solutions don't seem to have the ability to mark traffic at the ser...
Hi, I issued the command:switch 1 renumber 2The change won't take effect until a reload; wondering if there is a way for me to cancel that operation as I made the change in error. For that matter, is there a command to show all pending operations th...
Hello everyone! So, I'm going from a Cisco 891 router to a Cisco 3925 router with a built in T1 card. The 891 had a switch card so I could use all sorts of Layer 3 switch commands YAY! But the new 3925 (wholly huge batman) does not. So, I'm not u...
Hi guys,I am trying to setup a backup internet connection to an ASA for Remote VPN in emergency cases where the primary internet conncetion is unavailable. The two internet connections should wouk side-by-side for Remote VPN login. The problem is alw...
Hi all,I'm working on a network design with several offices and dual WAN connection. Now I'm testing it in a lab, but one router (RTR04) keeps freezing after a link failure (only with multicast enabled). You can see the lab topoplogy in the atachment...
I a using a Ciscoet 2800 Series router with a Call Manager 5.0.1. When I make a call I g this error:*Dec 12 20:30:38.575 Potential Mute Call:*Dec 12 20:30:38.575 Call ID1=3 Call ID2=4 ConfID=2*Dec 12 20:30:38 575 Leg1: CallID=3; TX Packets 398; RX Pa...
I have facing problem in accessibility from outside in following scenario. I have two internet connection from two different ISPs said ISP1 and ISP2, Goal is both ISPs work in load sharing manner,PPTP VPN traffic goes to ISP2 from Interface Fastether...
Hi there,I´m having trouble connecting to the internet with the 877 router; I have tried several different configurations, but I always fail to connect. The Telecom said that the line is Ok, and in fact I´ m able to connect through the old Alice mode...
Hi,Hi, I need the model ISR router for use with two 100MB internet links with load balancing and failover, at first I'm thinking about the 1900 series, and would use the SCAN SAFE (CWS) to filter web content, This equipment would support two links 10...
I'm working on a casino network which comprises of two different networks. Connecting the two networks is a transit switch that is pretty basic with only a management IP and a default gateway. That links into the gaming network's core and the operati...
Hi Guys,I was wondering if a Router 2911 could handle three Ethernet WAN links of 200Mbps each.Basically what I need is to handle 2 WAN links as Primary and 1 BackupThanks in advance,
Hi;I hav a ASA5512X firewall with 6 interface, interface 0 has been assigned to a WAN connectivity with ADSL, in which my ISP gave me two static IPs (not a block range of IP), my ISP mapped the Mac address of an interface to a ip address, this is wha...
.jpg "Hall of Fame Master"){kind=icon}
.jpg "VIP Collaborator"){kind=icon}
