Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

QoS and control traffic

Can anyone please explain how control traffic (routing protocols, HSRP, L2 signaling, etc) is handled by a router in conjunction with a QoS policy?  I'm looking for specific references please .  I can't seem to find anything that is clear about the s...

dbass by • Level 1
  • 922 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Load Balance and Failover using EIGRP

Hi All,We have this network (please refer to the attached file) which I want to configure loadbalance and failover on the remote site using EIGRP. How can this be done? Please note that links on the remote sites has different bandwidth.Your help is m...

cmadiam82 by • Level 1
  • 708 Views
  • 2 replies
  • 0 Helpful votes

Resolved! WCCP Service Groups and Redirection

I understand the basic concept behind WCCPv2, but I'm having a difficult time grasping the concept of service groups and redirection. We are trying to use WCCP with Riverbed. Can someone provide me with an easy to understand explanation, link or vide...

Resolved! Simple Network & Aggregate address command

Imagine someone tells me "I want to advertise network 150.33.36.0/23" via BGP. Then I am given the following config regarding this:(...)router bgp 100 network 150.33.36.0 mask 255.255.255.0 aggregate-address 150.33.36.0 255.255.254.0 summary-only(......

news2010a by • Level 3
  • 499 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Two Default routes

Hi Expert,Attached please find the existing network block diagram and relevant config for your reference.HK: router to ISP - Arouter ospf 192network 192.168.0.0 0.0.255.255 area 0network 192.168.10.0 0.0.255.255 area 0network 192.168.20.0 0.0.255.255...

offset list

guys we always use access-list for an offset list....now i have seen in eigrp that offset list 0 has been used but there is no access-list??? can someone please xplain why is that....

First Ping fail

Hello,i have a problem with a cisco 857-K9 router. We can access internet but if we ping a web server, every first ping fail but all others works...I'm very new with cisco product, how can i fix it ?Thank you very much

Resolved! Static NAT

Hi.I have the following configuration and i want o add 2 IP addresses and map with two internal devices.How do i configure this?Regards Tommy SvenssonIP range between xxxxxxxxx.64 - xxxxxxxxx.79 where .64 is network address and .79 broadcastThis mapp...

Resolved! bit bucket into the routers - Null0

Hello,I’d like to put a bit bucket into the routers. I think i can save bandwidth and security things by dropping any rubbish.ON ROUTERS WITHOUT STATIC REDISTRIBUTIONint Null0exitip route 0.0.0.0 0.0.0.0 NUll0ON ROUTERS WITH STATIC REDISTRIBUTIONint ...

ohareka70 by • Level 3
  • 1963 Views
  • 3 replies
  • 0 Helpful votes

BGP Loadbalancing with multihome network

Hello All,I have a scenario like this, using bgp in a multihomed network with two different ISP. my intension is to acheive loadbalancing in both inbound&outbound direction. I have subnetted my prefix 82.x.x.0/24(for example) into two 82.x.x.x/25 pre...

bava_ccna by • Level 1
  • 1381 Views
  • 8 replies
  • 0 Helpful votes

Cisco 7609 - Enable Password Unable to Break.

Hi all,Cisco 7609 Router, Enable password unable to reset.Many times CTRL+BREAK Key combination while booting the router does not takes the console to ROMMON.Router boots using the IOS image in the bootdisk0: (For entering into the ROMMON, removed bo...

View All
Review Cisco Networking for a $25 gift card