Resolved! One 10G port for SVL Link
Can we use only one 10G port for SVL Link and one 1G port for dual-active-detection link in stackwise virtual switch configuration .
Forum Posts
I have a question, How to activate C9400-SUP-UPG-LIC= LIC?
I have a 4506 SupIV with several vlans, and want to move the vlan.dat file from the old Sup to the new. In addition, the new SupV actually has existing vlans on it I wish to delete.I tried copying the vlan.dat file from the old SupIV in the cat4000_...
We are attempting to look up product information, and are getting back incorrect results. For example, when looking up the PID PWR-IE50W-AC-RF, we get back one correct result ,the product_type : POWER and others are incorrect results,Images,Subcatego...
Dear all, I have CISCO Catalyst 2960 SI POE 24. I am palnning to install CCTV over POE. I would like to know what is watt and voltage that each port can provide please.
Hello,I have a portchannel with two 10Gig ports. There are two VLANs in trunk in this portchannel and I would like to limit the bandwidth for the vlan as follows:VLAN1990 - Allocated 1GbitVLAN1991 - Allocated 19Gbit VLAN1990 is vlan with multicast TV...
Nexus9504 ver is 7.0(3)I4(6) Traditionally, X9536PQ module 1 and 2 are usedModule 1 and 2 ports, module 2 ports, vPC peer-link was being usedModule 1 is X9536PQ and module 2 is X9636PQ due to module replacementPeer-link is not 160G after X9636PQ repl...
We have six gas meters that have worked without issue for over eight years. Four were supported by IE-3000 switches. Recently, we replaced two of the IE-3000 switches with IE-3300 and within hours began having problems with loss of connectivity to t...
I've been experimenting with connecting the "core" 2 stackwised 9500(which supports Pagp and LACP) to the "edge" SG350(which supports just LACP?). The LAG on the 9500 consists of 2 25gb ports 1/0/1 and 2/0/1 and the LAG on the SG350 is 2 10gb ports...
Resolved! Cisco Nexus Allocating Interface
I am trying to allocate an interface to a VDC but am getting the following error: ERROR: 1 or more interfaces are from a module of type not supported by this VDCThe chassis is a Nexus 7000The module in question is a N7K-F248XP-25EWhen I do a show vdc...
Hello guys, Our C3850 switches' CPU high frequent. #show versionSwitch Ports Model SW Version SW Image Mode------ ----- ----- ---------- ---------- ----* 1 16 WS-C3850-12XS 16.6.5 CAT3K_CAA-UNIVERSALK9 BUNDLE2 32 WS-C3850-24S 16.6.5 CAT3K_CAA-UNIVER...
I currently have 2 NPS servers(Windows 2016) that server as Radius hosts when logging into remote switches. Is it possible to add a third server that resides in Azure - we have a site-to-site tunnel setup. The new server is a Windows 2019 edition and...
Resolved! File too large for TFTP Error?
I am trying to download the c2800nm-adventerprisek9-mz.124-12 on my Cisco 2811 router, but on SolarWinds TFTP server it is showing an error message that file is too large for TFTP protocol. what is this? How can I download this image to my router?Pls...
Hi Team, We need to configure password policy for the Cisco C1000/9200/9300/9500 without AAA model.
Resolved! Nexus 9k upgrade from 6.1 to 7.0(3)
Hi, Preparing for Nexus 9k upgrade from 6.x to 7.0(3).l7.4. However i have read due to few caveats, it is good in two stage upgrade i.e. from 6.x to 7.0.(3).l3-l6 etc. and then instal 7.0(3).l7(4). best regards
