Activity in Technology and Support
SNORT GID 2: Tagged Packets
I came across a configuration guide which mentions, in the Intrusion Policies chapter, GID 2 as " Tagged Packets. (Rules for the Tag generator, which generates packets from a tagged session. )" https://www.cisco.com/c/en/us/td/docs/security/firepow...
ACL is blocking HTTP(s) even though it is set to Permit
Hi all,I'm working on a Packet Tracer project, and I am stumped as to why my ACL will not permit traffic from port 80 and 443 to my web server. With the ACL not binded to G0/0/0.40 I have full access to the web server (HTTP(s), ftp, ping). When I bin...
ACI L3out Pair Firewalls
Hey folks,I'm looking to set up an L3out with static routes for an Active/Standby Firewalls pair, as shown in the diagram below. However, I'm feeling a bit confused, especially when it comes to configuring the L3out with SVI. Any advice on how to pro...
Cisco 9300 switch doesn't connect via SSH
I have a couple of switches that are trunked via a LAN cable from another switch. I noticed that these switches sometimes have a hard time to SSH into. I get the error: "Connection timed out". After a while and a few tries I can connect just fine. I ...
IKEv2 SA drops immediately
Hello,I want to set up a IPSec IKEv2 VPN to a central ASA. On my side we have a cisco 897.First I tried a crypto map configuration. Didn't work because the IKEv2 SA goes UP and immediately goes DOWN with the error message "IKEv2:(SESSION ID = 1,SA ID...
NCS2006 shelf menu
Hi, a dumb question i'm logged into the shelf remotly via CTC, I have the shelf view but cannot find how to open the menu
How See advetise route by any details in nexus
Hi dears if i see advetise routes prefix to nieghbor X.X.X.X by details for example which community send wightand other bgp parameters How can see thisin bgp nexus switches for examples 9K series???
Default VLAN Migration
So this is a topic that's been mentioned time and time again I'm sure but i wanted to get a bit more specific to my situation. We're replacing our core switch with a C9300 (we currently have a 3750). We have a pretty simple network. Any desk with a c...
FTD Multidomain
Hi ALL , We are planning to move our production FTD from the global domain to the leaf domain. Will it have any impact on traffic?Br,SS
Resolved! FUS and IOS Update for WLC2504
We purchased a Cisco WLC 2504 and Cisco Aironet AP1815I for use in the classroom as part of our Cisco Academy. We are a community college and do IT and CCNA training for students. Students were working to get the AP's connected to the WLC and through...
Cisco 9115AXI EWC cannot access to WebUI remotely
Hi all, I have an issue with my Cisco 9115AXI EWC where I can't access via WebUI. I have enable the http and http-secure server as well but failed.I have saw the traffic that pass through the firewall (Palo Alto), it shows that the application incom...
Issue forwarding calls CUCM > WEBEX > PSTN
Hi allwe have implemented some trunks from out CUCM to a CUBE then to webex.we can call the extension from the cucm on webex and it works fine.we translate the source of the call and prefix it with 8801, so webex sees the 8801 plus the extension as t...
SD-WAN EEM Support
Hello, An organization wishes to to track monthly usage of 4G LTE interfaces on an ISR. When that amount of traffic is exceeded within a monthly period, traffic sould reroute from the cellular interface (by automatically “shutting” the cell interface...
Cisco wireless controller 2504
Dear all ,I want to support me I have wireless controller 2504 connect to device access point but I can not enter webpage so I want configuration this device but I can not enter webpage Best regards
Consult transfer intermittent failure with Teams Direct routing
Got CUBE in Direct routing setup with Teams Phone system. If an external mobiles calls into Teams and performs a "consult transfer" to another mobile it intermittently (2/10 times) get transfer failed. Note REFER method is disabled due to other issue...
| User | Helpful Count |
|---|---|
| 137 | |
| 119 | |
| 94 | |
| 78 | |
| 54 |
