Activity in Technology and Support
How upgrade Cisco Prime Infrastructure 3.4to3.10
Hello,Now WLC has launched some 9115AXI and found that version 3.4 cannot recognize these APs. Should we upgrade each version one by one or can we directly upgrade across versions to 3.8 or 3.10
Wireless Design / External antennas
Hi all,it's some time ago when I designed a larger wireless infrastructure in an industrial/warehouse environment. Back then it was standard to use APs with external antennas to meet alle the challenges (high ceilings eg 7-15m, very long floors with ...
WLC 3504, 802.1x clients are disconnected sometime
Hi guysMy office is using WLC 3504:With some Cisco AP:Users complain me, they are often disconnected to the wireless (802.1x) 5-10 times a day.I tried to debug a client and this is the log when it was disconnecteddebug client log is in the attach fi...
Resolved! 9800-80 active and standby configuration out of sync - 17.12.4
I am attempting to upgrade our 9800-80 HA pairs to version 17.12.4 to resolve a certain bug. The upgrade from 17.9.5 went smoothly in the lab, but upgrading a pre-production pair from 17.9.4a has resulted in the standby being in a boot loop with the ...
C3850 upgrade failure
I wanted to upgrade the C3850 in stack from version 16.12.8 to version 16.12.11 in BUNDLE mode.The steps I followed: 1. copy tftp: flash: .... -> successfully 2. no boot system 3. boot system switch all flash:cat3k_caa-universalk9.16.12.11.SPA....
Restoring back a Client who was REMOVED using Cisco Prime
Hi, if I have remove a client using Cisco Prime Infrastructure how do I re-enable or allow it back in to the network.
Increment contact priority in queue in WxCC
In one of my UCCX scripts I increment priority of the call as it waits in the queue. So call entered the queue with low priority and then I keep incrementing the priority using 'set contact priority' function in UCCX as contact awaits in the queue. H...
IPsec over NAT444 issue
Hello Everyone I have to set up an ipsec tunnel with Lo0 as source of tha tunnel. Nat is activated in My CE and in the ISP level (NAT444)All ipsec and Nat configuration is ok but, and as I know that for the NAT to work correctly, the packet should pa...
Using DNS to resolve switch hostnames for NTP
Hey all, I'm pretty new to all of this, I just passed the CCNA in June, and have been working as a jr. Net Eng/Admin of my company for about 8 months now.I was asked to configure our core switches at our main office as NTP for the rest of our network...
Installing and using OpenSSL tool
I am trying to install the openssl tool detailed in this guide - https://www.linkedin.com/pulse/anyconnect-ftd-pkcs12-openssl-matt-albrecht/I have the openssl-3.2.3.tar file. But not sure what to do next, I have a Windows machine..
ASA performance test using iperf3 - NAT problem
I tested the ASA 5520 iperf3 to check its performance. I then wanted to add NAT to it to find out how much it was taxing the device. However, I kept having the problem that almost all traffic was untranslated.The created objects are the same, i.e. 19...
EVPN VPWS problem
HiI was wondering if anyone can help me out with a problem regarding vpws.I have set up a lab and followed the asr920 guide to configure evpn-vpws ios 16.5.1 but can't seem to get it to work.The VC comes up but I see no next hop or anything.From what...
ASAv AnyConnect Azure SAML Integration
I'm working on an ASAv deployed in Azure and had a working AnyConnect configuration using LDAP to a DC in Azure. I tried to setup SAML with Azure AD today and while it appears to be partially working, users are unable to connect. This is my configu...
BGP prefrence over static Routes
I have a setup in which i have 2 routers connected to same ISP A both via default route pointing towards ISP for internet.Now we want to add another ISP B on both routers however that ISP will use BGP with RIPE IP address over the internet.Now we wan...
Monitoring network traffic from a multicast IP address
I am trying to figure out a way to monitor network traffic from a specific multicast IP address and port via SNMP. I've found the MIB files that for the Catalyst 2960 + switch and I have been trying to use the iReasoning MIB browser to view the MIB f...
| User | Helpful Count |
|---|---|
| 162 | |
| 137 | |
| 102 | |
| 78 | |
| 67 |
