Our wifi network consists of:vWLC (upgrade from 8.6.101.0 to 8.10.130.0 did not solve the problem)31 x AP (7 x AIR-AP2802I-E-K9, 24 x AIR-AP1815I-E-K9)Flexconnect mode (I think local switching or not does not affect anything)To not ruin any settings ...
Forum Posts
Hello Professionals,I just wondering if I could make HA SSO physical WLC9800 and virtual 9800.I have 3 WLC9800-L and two of them will be gathered as HA SSO and one left.Just wondering if I could make HA SSO mixing hardware/virtual.Have anyone tried o...
Hello, my APs and my WLC have a different Softwareversion installed after upgrading from 17.9.5. to 17.12.4 with APSP. My new WLC-SW-Version has 17.02.04 and my APs has 17.3.6, they are running together perfectly, except one AP C9136 that wont connec...
Resolved! AP802 Module in 1941 Router.
I have a AP802 module from another router a 892w and I saw that the 1941's do have a wireless version, so I wondered if it's at all possible to use that module in one of them?If not is there a way to add wireless to that router via another method?Any...
We are trying to setup a AP Mesh topology between our two sites with WLC 9800 but it doesn't worked yet. and aslo we don't have the Mesh menue under Configuration > Wireless >Access PointsWLC: 9800 Amsterdam,17.3.4cAP: C9115AXEWe followed the instuct...
Hi all, I have recently converted a C9115AXI successfully using the steps below: https://www.cisco.com/c/en/us/support/docs/wireless/embedded-wireless-controller-on-catalyst-access-points/215303-embedded-wireless-controller-conversion.html I did exac...
Hello,Before updating my Cisco C9120AXE (fw was 16.x) I was used to change the country code with the following commands over SSH:enableconfigure terminalap dot11 24ghz shutdownap dot11 5ghz shutdownap country <country_code>no ap dot11 24ghz shutdownn...
We have spun up the Cisco Catalyst 9800-CL Wireless Controller from the Marketplace in Azure. We have tried both the virtual machine ad the virtual application, and in both instances, when you ted to add VLAN under the Layer 2 > VLAN > VLAN page, the...
Resolved! WLC keep reloading automictically
Model: AIR-CT5508-K9Version: 8.1.131.0Timestamp: Wed Oct 5 19:10:29 2016SystemUpTime: 0 days 2 hrs 24 mins 8 secssignal: 11pid: 1155TID: 1047323456Task Name: capwapHATaskReason: System Crashsi_signo: 11si_errno: 0si_code: 1si_addr: 0x1d66fac8timer tc...
Resolved! 169. IP
Anyone come across a situation? Clients connected from one of the APs on the network suddenly valid IP convert to 169. IP and loose the connectivity After the restart, the AP will give a valid IP.2802 models AP and connected Cisco Virtual Wireless Co...
Resolved! C9120AX-C Not able to join 9800 WLC
C9120AX-C was previously joined to the controller, but for some reason it stopped working. Upon checking it disappeared from the controller. The last join attempt stats below
HIWe have switches connected over a wireless bridge, however VTP information is not sent across correctly.I have seen old community posts with older models, wondering if there is any official Cisco document suggesting that VTP will or will not work a...
Hi,There is C9120 EWC with 17.6.4 IOS-XE.Now I plan to add IW6300 into this EWC. It shows below error informationAP Image Version 17.3.8.21 backup 0.0.0.0, Controller 17.6.4.56 Version does not match.How to upgrade IW6300 version to compatible with E...
I have a problem when I enable PEAP in the Flex profile for the one site, the following error appears:Error in configuring Flex profile - AP local auth is not enabled
Hello everyone, I´m from Argentina, it is not easy to get equipment here, my supplier abroad can provide me the Access Point but not the licenses, is there somewhere where I can purchased directly from a website with a credit card?Thank´s in advance
