Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Everyone,I'm having a problem in my new topology;IP Phone -> CUCM -> H.323-> CUBE->E1 PRI -> ISPand also a TCL is running as basic greeting message on CUBE so When a call comes from outside IVR is running properly then when someone press "4" it...
Here is the config, line is in port 0/1/0- ignore 0/1/1. Debugs after config. Call fails to 14043940384. Any thoughts? MADRAS-2811#sh runBuilding configuration...Current configuration : 10579 bytes!version 15.0!hostname MADRAS-2811!boot-start-markerb...
Hi there. We're running CUCM 9.1.1 with SCCP phones, and transfer has stopped working.We've tried this from several phones, and get the same result. A user can hit the transfer key to put the caller on hold, dial and connect to the number to be trans...
Hi,We have a requirement to prefix calling party number with 1 while routing a call to ITSP's SBC trunk.I did the following --1) created a partition (PT-1), created a calling party transformation pattern (CPT-1) and applied to PT-1 and a CSS (CSS-1) ...
Our company recently upgraded to a new CUCM version, server etc. In the process a lot of cludge (old route patterns, translation patterns etc) was discarded to clean it up, as well as converting to a 6 digit dial plan vs 4.Our campus is the Corp HQ ...
Hello Team, I just logged into my PG1 and I noticed the attached error messages. Can I ask if anyone has seen these errors before? Please see the attachments. I am running legacy ICM 7.x with CAD.
Friends,I have a little bit problem withe the audio files. My client has a lot smartphones for their employees. All smartphones has completely dropped support for wav files. Is there anyway to convert the wav files to mp3 before they are sent as e-ma...
Friends,I´m creating an Estimate in the CCW tool and I´m adding parts of a Cisco 2901 Gateway. However the IOS is a little different of the DSP calculator shows. In Estimates and Configuration (CCW Tool) you can see: S29UK9-15401TS29UK9-15501TS29UK9-...
hi all,we have situation. 2 CUCM 7.1.(3a) (Pub+Sub) based on MCS-7825-H4.we had a failure on the raid. We have replaced the failed part and the subscriber is up and running "standalone" (we see on CLI the hostname and this is correct also we have tes...
Hi, Hopefully this is the correct place to post this request for assistance from the experts. I have a customer that has CUCM v11 operational on site and we have some devices that run the Linphone client that connect via SIP extensions to the CUCM. ...
Hi community,I was wondering if someone knows how to replicate, for example, from CUCM’s Informix database to an external one (Ex: MSSQL or MySQL). It is for troubleshooting purposes.Remark: I don't like to work directly on the CUCM CLI.I have seen t...
HiIn one router we have 8 FXO ports connected to different numbers.But in outgoing call we only want one caller ID number to be displayed on outside phone. and rest of the numbers should not be displayed.I created Voice translation rule and calling p...
HiWe have Call manager in our HQ and some phones in Branch in a different country. From CUCM there is a SIP trunk towards router in branch.Users in branch occassionally complain of phones getting unregistered.HQ and branch are connected through inter...
Hi Experts, In my project PO, there is 7965G IP phone for reception and 7916 expansion module, My question is there is no power adapter for 7916, I have just PoE from 2960s switch, Do I need extra power adapter for 7916 when connect to 7965G? Thanks,...
Hello, is is there anyway a phone can automatically dial another ip phone internally without a user ever dialing. Like can there be a virus on computer or phone that can cause it. Keep in mind the two phones call log shows the dial call. We have call...
