Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Everyone,I have a more than 100 IP phones connected and working on a Call Manager Business Edition. However these phones need to be migrated to another Server running Unified Call Manager Enhanced version 9. A simple migration from one machine ...
Hello, I have the numbers which are 7 digit 8002111,8042222 and they are working good with the below configuration.dial-peer voice 800 voip description ** Outgoing Calls Toll Fr translation-profile incoming dialed destination-pattern 98[024]....
I want to test VPN Phone in the ASA5520,but "show ver" find the "AnyConnect for Cisco VPN Phone : Disabled", www.cisco.com/go/license i didn't find register AnyConnect for Cisco VPN Phone demo license, how to apply for the demo license??Licensed feat...
Hi UC experts,I have a strange issue with analog devices connected to a VG224 GW. We have configured cptone de under the voice ports. Normally there are two states of different tones with phones in Germany:1) You go off hook - a short periodic beepin...
Hi,I have a BE6000 server, with CUCM 9.1 deployed which includes Cisco Unity. One Guest VM with both Call manager and unity on it. I have a router running in SRST mode all on the same site in case of CM failure.I would like to have Vmail functionalit...
Hi,My ITSP has requested that I send different port for a specific range of numbers:Example:When I dial -- 123456 It should be sent to sip port 5000When I dial -- 6789 It should be sent to sip port 5001I tried to change the port in the dial-peerdial-...
I have a client who is getting random disconnect errors from his cucm servers. They seem to encompass other network errors at times as well, but not always. I'm having a hard time telling if its cucm or if it is a network issue in general.I pulled ...
Hello All,I configured Cisco 2921 as SRST router and H323 gateway. My phones (Cisco 8961) are registered.I cannot call in from PSTN and pickup the call, but for some reason I cannot dial any extension or PSTN number.Config and show commands in attach...
Is there any way to play congestion/busy/any other tone to the caller when the callee is speaking on another line on same phone?Update: While playing busy/congestion/any other tone to the caller the call have to ring in second line on receiving party...
I've been trying to think of an efficient way to shun or divert incoming calls if the caller has their caller-ID blocked or withheld. I have this setup in a working home environment (lab). The problem I have is, how can I match on *nothing*? I though...
We have a customer they are planning to migrate the License from DLU to ELM,total 400 units Now the customer is planning to purchase a Cisco buisness edition 6000 want to import the License to ELMIs there any License Calculator available to check?Wha...
Does Call Manager v8.5 support paging on mulitple phones (groups of phones) simultaneously or does it require another product? We purchased IPSESSIONs a while back to use for paging but I was told that the function was in Call Manag...
Hello,Can someone point me to some examples to use a jump server to control Esxi and CUCM.Also does anyone have a document that descibes security bestpratices for CUCM.Thanks,
Currently out business is set to hit a call tree at 5pm. I need to change this to 6pm. We are running CUCMBE 8.6. I cannot seem to figure out where the setting is. Can anyone help me?
Hello,For most incoming calls coming in on FXO lines we are noticing that there is a 8-10 seconds delay before the audio is established. Call comes in, IP phone rings, then there is 8-10 second delay before either party can hear anything. GW was re...
