Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Pros,Facing a issue with CM 9.1.1 & 8945/6941 IP phones. Whenever we login to IP Phone Personal Directory > Personal Address Book & try to create new Contact and click submit to save it gives a PD Error Message There was an error adding the entry ...
In Cisco CME 9.0, how do you enable the USB port on the 8961 phone handsets for headset usage?It worked fine in the default phone shipping configuration until I created proper per-phone profiles under voice register on the tftp server.. so something ...
Guys,Need help... Has anyone managed to get Cisco Telepresence working with Cisco Unified CME
Hello all,We are upgarding CUCM from 6.1.3 MCS to 9.1 UCS. Our plan is to jump from 6.1.3 to 6.1.5 to 9.1.We took backup of 6.1.3 MCS via Disaster Backup Recovery & restore it at UCS after new installation of 6.1.3.We contacted cisco licensing team t...
Hello, I'm using old 2800 router with telephony service 7.0(1) and SPA 7911 which is now impossibly to get. I need to buy 2 phones similar to 7911, is SPA 512 g will work on my router with ios 12.4 and telephony service 7.0(1) ?
Hey Guys,7937 registered to CME doesnt register anymore but keeps on rebooting.Firmware apps37sccp.1-4-4-0.bincant factory reset either can some help. Debug tftp events shows the followingOct 22 11:26:36.905: TFTP: Looking for RingList.xmlOct 22 11:2...
Hello All,I have an issue with fax, it is connected to an fxs port on my h323 gateway. When a call comes from PRI and get connected to fax after I hear the fax tone the fax drops. IOS is Version 15.0(1)M4, and DSP is PVDM3.My analysis:The external ca...
Hi,I'm using CUCM 8.5.I'm testing click to call feature. I did the necessary configuration in call manager and installed click to call application in client desktops and configured.NOw the problem is,In call manager LINE 1 is VOIP an...
Hi guys,I have a CME router with both SIP dial peers (preference 1) and FXO PSTN dial-peers for failover (preference 2). When SIP is unreachable, you go to dial a call, it hangs on "Ring out" for a minute or so and then returns busy tone/unknown numb...
Hi ,In our scenario some of the users moved from Cisco to Lync Endpoints for the POC & at the same they will get a call from Existing directoty Number in Cisco as well.I have tested with configure the "SIP URI" in Remote Destination & configure the D...
Hi community.I think this question could be very easy to be answered by the experts in cisco voice calls. What are the necessary steps to configure all internals phones that they have to dial a prior "0" to get an outside/international call working? ...
Hi, We are getting the "Failed to update error" when we try to add new agent in agent explorer. We can overcome this only if we provide another pheripheral number for the agent.Please suggest some tips to overcome it without the help of database..The...
Hi ,I am searching the space required to back up the CUPS , CUC , UCCX disk space , this is requested by the customer ,can anyone please advice on this since im unbale to find the exact details in the documents ..regardsPurna
Hi Call flow as below:phone 8945 -----sip-----> CUCM ----- sip trunk ----> 2900 ----- T1 ---> PSTNWe have a site located in USA which expereience international call to certain country failed.Calls to Japan is fine but failed to Germany and Brazil. Th...
we have an enviroment consisting of 1 Publisher 6 subscribers and 2 tftp :Production : Pub sub1-sub2-sub3 tftp1DR : sub4-sub5-sub6 tftp2we were testing DR we shutdown :Pub sub1-sub2-sub3 tftp1All Phone work fine except the 7940-7960 model ...
