Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Everybody,I'm a newbie in voice... now I'm trying to configure the SRST mode in VGMy lab test includes CUCM8.6, VG (SRST), and all IP phones are SIPI have successfully fallback to SRST mode after unplugged the CUCM from the networkHowever, I'm sti...
Just a quick question... not being a QOS guru or anything, am looking at one of our sites setup by someone else and trying to determine why you would use both Auto QOS on a port and:mls qos trust device cisco-phone mls qos trust cosWouldn't these be ...
I am trying to determine which OVF to use with Unity Connection BE6K. I have found a specific one for CUCM but don't see one for Unity Connection?
HelloPlease advise. We have just implemented CCME into one of our remote sites. Is it possible to access voicemail from home by dialing in ? and if so how do I set this up.Kind Regardsscott
Hi, I have a little problem with a voip call between two sites, i am new at VoIP.First let me explain my scenario, I have two sites, each at different cities, they are connected using a Cisco site-to-site VPN, Site A (Cisco 2811), Site B (Cisco C1861...
I do not know if this possible, I need to assigned one softkey to Personal Address Book, and assign default ID and PIN for this PAB for all users.Thanks,Ali
Hiwe're running UCM 7.1.3 and currently using the UCM internal database for directory lookups. I want to change this so that UCM pulls data from AD via LDAP. The problem I have is that the UCM database listed users extensions in 4 digit format and in...
Dear All,I have installed IMAP Client on Lotus 8.5.2, after configuration i am able to see the Voice Mails in the Inbox, but the Inbox having the "DEMO" oil print on page, since it is Compliance matters i would like to know how to remove that, furthe...
Hi GuysI have run in to a mysterious upgrade. We are helping a customer to migrate from an old CallManager running 4.1.2. We are using and old MCS 7816H3 as a physical test server. The server is updated to 6 GB RAM.First step is to use the DMA migrat...
Hi AllI'm working on to troubleshooting voicemail improperly issue on unity, I would like to enable marco trace on cisco unified serviceability , but i can't found any about that on there, anyone know this ?
Hi Folks,I'm trying to get a single 7970G phone to register against a 2611XM running CME 4.3 as part of studying for my CCNA Voice. I've done lots of reading around and come up with the config attached, but the phone I've got just sits at the Upgrad...
Hi,I wanted to get an opinion of what would be a good microsoft class to take to learn active directory. I know the basic stuff like most people do. I am looking from the percpective of integrating Microsoft and Cisco apps (jabber, lync, etc) and b...
Dear all, I try to register 7941G phone, (firwware=SCCP41.9-1-1SR1S) with MIC to CME with 12.4(20)T2 in UC 500, I already set up the CA, tftp-server, cme-server, capf-server, sast1,but no work, here is the configuration, Please advise, many thanks.R...
Dear All,I am running CME 7.1Having one E1 line and 8 Fxo ports.E1 line is configured properly and the DID/DOD extensions are assigned to the ip phones.Now i need to configure the 8 FXO ports in such a way that the second button on the 7942 ip phone...
hi all , Can you please help me understand the purpose of signaling forward rawmsg cmd under dial-peer config on cisco router ??Many Thanks Anil Sharma
