Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi guys, Q regarding Path replacement.We have CUCM v7.1.5 linked with some Siemens PBX's. Path optimisation works in most cases very well. In soms cases it also works but too well. Let me explain.Call comes in via CUBE (SIP trunk). Call is sent via Q...
Hi All, Customer would like the the ability to restrict of release outbound CLI. Previously they had the 9.@ pattern set to prefix with 141 and and 8. pattern to release CLI. Changed the solution to route out a CUBE instead of MGCP gateway. As 141 no...
I have two locations connected via point-to-point wireless link, the Main office has the CUCM ver4.2 with 8 phone lines. The second facility is a charter school. Many customers and parents complain when they call the school number it is always busy. ...
Here is the topology:fax->ata->cucm->h323 VG-------->mpls---------->h323 VG->PBX (through E1) ---> faxI have a very very bad fax quality or half pages ONLY from this way..Any ideas of wha to check..?Thanks
Hi,If i configure IDLE URL in enterprise parameters of CUCM 7.x, and when later when user login into a phone using Extension mobility, will these IDLE URL will still be working or it will be over written. Device profile does not have IDLE URL paramet...
Hi,I have configured a SIP trunk in CCM. There are no problems with incoming calls but I need to change SIP headers for outgoing calls. I need to send host name instead of IP address and I need to add "user=phone" in the header. ieINVITE sip:6303333...
Hello,I have a problem with the UCCX which displays error on the Backup page as per the attached:• UCCX System version: 8.0.2.11003-10• Installed on Linux admin: show version active Active Master Version: 8.5.1.10000-26Acti...
hi,Currently we are having a call manager 6.x version and it does not support ATA 186 anymore. All the branch routers are cisco 1841. Is there any way that we can plug FXS card to the 1841 branch router and configure?If yes, how?If no, any other solu...
Dear friendshow can i identify if my gateway is registered and online .. means in my enviorment we have multi tanent stuff.. means multiple BRI isdn lines conimg and temination on cisco 3825 and their own seperate card. when ever a line goes down i n...
I am starting to configure a 2921 with an ISM for voicemail.I've configured as follows, but telnet and ssh advises that the connection is refused:RTR#ssh 192.168.4.5% Connection refused by remote hostconfiguration that i have added:interface ISM0/0 i...
Hi all,We currently have our IP Phones connected to the switches (4 catalyst 3560). The Callmanager assigns the phone's ip by DHCP.Our data and voice LANs are completly separated, logically and physically.We want to use the IP phone's switch to conne...
in the 28xx CMEmax-ephone = 24 (# of sccp phones can be registered)now I have 24-ephones?I want to register more phones?Can I use sip phones instaed of SCCPAgain max # of phones registered (sccp+sip) is 24?
I'm getting the following error when I make a voice call into a new 3945 with a NM-8CE1T1-PRI voice card:*Jun 17 00:40:21.479: ISDN Se1/2:23 Q931: RX <- SETUP pd = 8 callref = 0x0004 Bearer Capability i = 0x8090A2 Standard = CC...
After a power failure at a site the cisco phones is giving the following message" Link down limited functionality"I have checked the config and also checked that the WAN links were up. Restarted the Gateway and the phones and still getting the same m...
hi ,does anyone know what went wrong ?- Phone A call reception 3134000, then reception at 3134000, transfer call to 6000, however reception can't talk to 6000 before she transfer to 6000.Everytime she press the transfer, user 6000 always hear MOH , ...
