Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Freinds,i need help to get our setup for mobile access working from internal extentions, we are able to get the call flow working from outside call,when call came from PSTN to extention configured for snr we are able to get the call on both, ex...
I have got a Phone CSS configured to have INT_PT, NAT_PT & LOCAL_PT and Line CSS configured to have BLOCKEDINT_PT & BLOCKED-XYZ_PT.INT_PT, NAT_PT & LOCAL_PT - Associated with corresponding Route Patterns.BLOCKEDINT_PT - Associated with the Translati...
HiI am going to upgrade my CUCM from version 7.1.3 to 7.1.5In 7.1.5 i can see 2 version one for restricted and one for unrestricted.What is the diffence between these two and what should i use.Appreciate your reply.
I need to export all of the phones from a 7.1.3su2 cluster to an 8.0.3 cluster. All system device pools, regions, profiles, PT, CSS etc. are all the exact same.I have attempted an 'all details' phone export and then all details import, but it appears...
Hi, hope someone can point me in the right direction.I am unable to make a call to CUE. When I dial the pilot number I get unknown number on the screen of the soft phone. I can ping cue and I have completed the cue initialisation. and added the dial-...
I made several changes yesterday to my routing in CallManager. When I run DNA using one of my gateways, it says route this pattern (it should not route). Call flow is:- <CallFlow>- <TranslationPattern Pattern="8.XXXXXXX"> <Partition>Everyone</Part...
Hi all,I have two BRI Lines on a CCME.1-BRI 0/2/02- BRI 0/3/0I have an extension 0036, if any body make International kal from 0036 extension, the call should be route through BRI-0/3/0 ...If any body make international call from any other extension ...
Hi Everyone,Hopefully this is the right section to be posting in.Can someone point me in the direction of some information on telecom regulations? I'm new to managing our Cisco Call Manager/VoIP environment and want to make sure that we're adhering t...
Any known good IOS for 3845 CME?
Hi community,I have a lab for preparing ccie voice including CUCM 7.0 running on MCS 7845 server. My problem is when i open phone config page to configure phone devices it takes too long to load the page i have to wait almost 4-5 minutes. it is sa...
I have a Cisco 2911 Voice bundle w/SRST and 4FXO ports. We are currently using the FXO trunks for outside calling (off net) to the PSTN.We are growing and I need to add more lines. I want to move to a full PRI and drop the FXO trunks.Which card do I ...
Hi,I have a CUCM 8 and a GW 2811 and I want to know how do I change the calling number.For example, my trunk number is 31325160 and my directory is 9061 if I call someone in PSTN I want to show the calling number as 31329061 not 31325160.How can I do...
Hi,I am looking for voip encryption solution, Cisco Canada(Montreal) said that this solution has never been deployed, at least in Canada.I can't believe that Cisco secure voip is not deployed in our government institutions which means that any networ...
Hi,I need help to configure TCL IVR in CCME. I configured it earlier with CCM version 7, but not sure how to configure it with CCME. Appreicate any of your help regarding this.BR\\Sagar
Hi Voice Experts?I have 4 sites connected through MPLS cloud and using Cisco CUCM 6.1 based voip solution for the internal calls.The bandwidth is with a premium CoS and dediccated for Voice.1, Location P - 1 Mbps bandwidth, hosting Cisco CUCM publis...
