Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
So I just read that Asterix has opted to replace the Music on Hold they have bundle with the server with some selections from a web site called Opsound.com. This site offers music shared by the musician under the CC-by-AS 2.5 license, which means fr...
Greetings! Just wondering if anyone knows which release of IP phone firmware supports SCCP version 20? I've been looking through topic and in the release notes without any success. Thanks in advance!
HI,I have integrated Tandberg VCS with CUCM 8.0.3 over a SIP trunk. I am facing below two problems:-1. When Tandberg phone makes video call to CIsco 9971 phone. The call gets disconnected after about 2 -3 minutes, On CIsco phone call gets disconecte...
Hi,does anybody know any "debug voip ccapi inout" output interpreter, which would display call setup-process-disconnect based on call ID?Quick orientation in the debug output is a problem, especially in case of many simultaneous calls.Thank you,Lubom...
Good Day All,I have a CM 4.2 (publisher and subscriber) that I need to upgrade to CUCM version 8.I am trying to get my head around the best process to follow.Prework- doublecheck the physical hardware will support 8.0.2c.7835-H2 with 2Gig RAM and 72...
Hi,i'm searching a particular type of function to associate buttons of an IP phone. I explain:I have Manager Phones with multiples DN configured on a single phone and i'd like to configure Speed Dial on these phones...but not the normal Speed Dial!!...
Hi all, i´ve been reading a lot of post about this topic. for example,https://supportforums.cisco.com/message/1090536https://supportforums.cisco.com/thread/297366https://supportforums.cisco.com/message/3038330And in all of them there are not solution...
We are having a sporadic problem with softkeys on one phone (7941). Periodically the soft keys dont change when on a call, which means the user does not have access to the hold, transfer, conf buttons. Instead the softkeys remain as they should when ...
Hi Team,I am using overlay config for 4 IP phones for one EXT# on CCME Router.I am using c sepeartor for the same.The 4th IP phone unable to receive calls directly by picking up the receiver, he needs to press Answer Button to take the calls while ot...
HiCan anyone help me recovery procedure for the admin password on a linux based unity connection box. I have a remote system i cant get in to and have to talk a local IT guy though the process.RegardsColin
Hi,i'm experiencing some fax quality issues after connecting 3845 gateways to ISDN PRI (with CUCM 7.1.3). I explain the steps of my Voip migration:7 days ago i had this situation:- Nortel Meridian PBX connected to 10 E1 PRI lines- fax server running ...
Hi,i have some slip errors that i think can compromise fax transmission. This can be caused by clocking configuration but i want to ask the correct clocking configuratin for a multi VWIC Gateway.I have a 3845 Router with 3 VWIC2-2MFT-T1/E1 cards (6 c...
I just took over maintaning a large VOIP system, which uses a Cisco MCS 7800 at it's core, running Cisco Unified Communications Operating System 7.1The problem I have is the system didn't have anyone looking after it before my arrival. I have a user ...
Hi All,I have a hunt group in CUCM with 3 members, 1082, 1077, and 1075. I have set the algorithm in line group as "Top Down", and reversion timeout as 15 seconds.The Busy is "Try next member; then, try next group in Hunt List". But still the call is...
Hi,We have 3 locations and have multisite deployment with Centralized Call processing ( HQ, Site A and Site B ). ISDN PRI E1 is connected to the gateway at HQ, and Site A.Now there is one more new location Site C having only analog phones connected t...
