Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
When I press the transfvm softkey I enter the vm # and press it again nothing happens.We have CCM 6.1.1
Anyone know why after we changed our TFTP server on our DHCP scopes, our 7940/7960 phones rebooted, got the new scope, but our 7910 and 7936 will not??? Tried factory resets, etc. Plugged a 7940 into the same port, it got the tftp... so I thin it'...
Hello,Using ACD 3.0 with hunt-group logout HLog.When all Agents are logged out I hear a few seconds of the en_bacd_allagentsbusy.au message before the en_bacd_disconnect.au. I was expecting to hear the disconnect message straightaway. Any help is wel...
I have two users that want their phone calls sent to each other. If some one calls Ext: 8001 and the person is not there they want the call to go to Ext: 8003. If some one calls Ext: 8003 and the person is not there they want the call to go to Ext: 8...
Hi, I'm running Cisco Unified communication Business edition version6.1.3.2000-1. The device protocol we are using for all phones is SCCP. I have two 7912 older phones that appear to be running SIP device protocol. The two phones are connected and ar...
I am operating Cisco Call Manager v7. It is purely the IP system, with no PSTN lines.We do have connections with other Call Managers in other countries, for which I use Hunt Groups to route the calls.I am trying to see if its possible to do 2 things...
I have an urgent need.I have a site that has reported over 4000+ minutes of calls from our Mexico site to the Ukraine. I am running CME7.x and do not know how to set-up toll fraud/restrictions on outbound calls.I need some help, point me in the righ...
Can multiple Unity servers reside in an AD domain and point to the same Exchange cluster? The reason I ask is because we are nearing our 512 CSS length limit and figure that if we can have 2 Unity CSS (1 for each server) then this may be a viable wo...
Is it possible to get info on changes made to the system by user and time on CUCM v5.1
Hi there,I will have a CCM 5.x and CCM 7.x in parallel. I will migrate user on the 7.x.I'm asking me, when I install 7.x do I have to know what patches have been applied on the 5.x so I will install them on 7.x too ( in case 7.x did'nt fix it ) if y...
I have a network with a UC500 connected to a 3750 switch going through an ASA.The ISP is currently having problem, so the site will be offline overnight.I have no experience with VoIP, so will this be a problem in the morning? When the WAN comes bac...
Hello,Is there a way to have CUCM automatically insert the special characters around the phone numbers in active directory, so that when a user searches for someone in corporate directory the numbers shows as (555)555-5555 instead of 5555555555??We c...
I have looked at a couple posts on my issues and cannot narrow mine down. Inbound calls to FXO fail basically. I used CCA to configure and inbound calls were first plar'ed to the AA. The call comes in and once tranferred to AA the call disconnects...
Get the following error while trying to upgrade to 7.1.2 Downloaded from Cisco's web site, and am doing local install. It detects the file, then hit next and get "The version number inside the selected upgrade does not match the filename"thanks
Hi peopleI am running the Dirt to 1108 mailboxes (W2k + Unity 4.0.5 + Exchange 2k). On 33 minutes, 869 mailboxes was copied. But on mailbox number 870 (Example Administrator), the copies were slow. Until this record was being used in HD 2gb, after t...
