Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I have ISR 4331 router with voice IOS with FXO card I Need to install Call manager express for 60(6921-10,7942-2,7962+7915-1,7975-1,7965-1,7945-1,6901-1 phones. And i need to have welcome message for my company. Could anyone advice what licenses ...
HI All Is this possible to test SRST with the following ways ? Also please tell me if there is any difference in testing normal SRST & SIP SRST. Method 1 For Example my CCM IP is 10.10.1.24Add the following route:ip route 10.10.0.0 255.255.255.0 n...
i have aproblem with my Pub and Subtwo server appear below message and can't login to PLM
Hello,Directory gets missing from the phones across the site.Phones displayed HTTP Error [500]!.Directory worked fine yesterday but stopped working all of the sudden. No changes made on CCME.IP Telephony and Phones, Unified CommunicationsSystem imag...
Hello, We have recently installed CUCM 12.5. When a user now goes into the Corporate Directory on the phones (8851's) they see "Offline" next to peoples names. I thought it was to do with "Presence" and if they were logged into Jabber this would chan...
Is it possible to obtain spare parts for Cisco handsets ? We'd like to be able to purchase replacement hook-switch assemblies for the 794x/796x phones. (See attached picture for the part we're after)GTG
I have cisco voip phone , model number CP-7841 , with cisco manager express.the phone can call only internal extensions, but I can't call landline numbers ?thank you
Hello People,We recently upgraded 78xx phones to latest firmware and did not face any issue so far. We performed several tests and looks okay. Phones are not getting disconnect, users did not report issue. Have you upgraded 88xx models to latest fir...
Hi AllAt first, I never use Cisco ip phone ever...I just bought 2 used Cisco ip phone and already upgrade FW to ver. 9-4-2-SR3.When I try to setting some configurations(some like disable LLDP, setting LLDP Power priority or QoS setting...),it just ca...
Hi, I am trying to disable video capabilities for IP phone 8945s in call manager. However, it gets triggered somehow and shows device video capabilities enabled. Has anyone come across this issue? It's a tricky situation because some 8945s in cluster...
Hello All,ATA 191 is registered to CUCM 11.5.1 and it is not working properly.Restart is required often to make it work.Note: There is an analog phone is connected to this device.I see no firmware information under phone configuration window, it is j...
Hi I have 2811 router with VWIC2-1MFT T1/E1 ... i have done the desired config on 2811 and tested the card Layer1 connectivity using Loopback tester..same Loopback L1 testing i did with NEC aspire PBX .. got success..But i don't know for some reaso...
Hi All, Currently we are running CUCME in srst mode registered with call manager 9.x using h323 protocol. The site has E1 connection for pstn and a spare e1 slot. We are planning to integrate cucm with legacy pbx via spare e1 port. There are few qu...
Hi, When we try to add shared line for Third-Party AS-SIP Device and Cisco IP Phone we received the message "Update failed. Shared Line feature is not supported".I can not find anywhere in configuration guides that shared line in not supported with t...
Hi All I am installing CUBE However, CUBE is not registered with sip-trunk.telekom.de. Please check the configuration and debug messages. sip bind control source-interface GigabitEthernet0/0/0 bind media source-interface GigabitEthernet0/0/0 rel1x...
