Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have 7835H-2400 with CCM 3.3. It is equipped with two disks running RAID1. Now, I will be upgrading CCM to 4.3, which requires (Win2003) 72GB of disk space. I would like to purchase additional two disks for each of 7835s so I can have two disks ...
Anyone used Intercom with CallManager 6.1.1 and 7931 Phone? Any issues? Does it use multicast, etc?Intercom is a Feature in CallManager 6.1.1, no Berbee or IPCelerate. Granted it's like Notepad compared to Word, but the customer is cost conscious.Con...
I need to set up a DID number that will be routed out the first Channel of a Voice T1 currently in a 2811. Currently I have this, but this will be going away..dial-peer voice 1 voip incoming called-number 800XXXXXXX dtmf-relay h245-alphanumeric code...
Hello,I am trying to upgrade to CER 2.0 on different hardware than CER 1.3 is installed on. We are going to use DMA to export the data. The issue is that while the new servers will have the same IP addresses as the old servers the new servers will ...
Hello -We are going to upgrade from Unity v4 to v5... Do call handlers and such get backed up? Is there a way to back these up? We have on-box VM, so I can use the exMerge tool to preserve the voice messages.Thanks for the reply!
We have a hq and a branch office with a CallManager located at hq. In event of a WAN failure, with SRST will the branch office users be able to reach hq extension numbers by continuing to dial just the internal extension numbers, or is it necessary t...
Guys,In SRST mode, can you dial the remote site from the hq( with CCM) using the same 4/5 digit xtension used during normal operation.People have said you can use numb-exp or xlation rules, but my question is since these numbers are DN, how will you ...
Hi,I`m assuming CUCM marks signal and media traffic as DSCP EF. Can anyone tell me if thats wrong ? Regards
HI Guys,When the agent receives a call I want the phone to ring for 3 rings and then go into auto answer..I am using IPCC enterprise and CM 6.0Is it possible??
Hi,How can I prevent one particular phone on the SRST site to register when in fallback mode. One way that comes to my mind is to have two device profiles and not have SRST reference in one of them. Is there another recommended way? Any command on Ro...
Hi,Could you please give the best solution to setup automated answer on phone number with re-direct?I would like to set a directoy number to be answered by a pre-recorded message which states the following: Welcome to XYZ - please press 1 if you look...
Environment:CCM 4.1, Unity version 4 also.3560s, 2801s. 6 buildings all linked by fiber. Each building has a 2801 and 3560.Total phone count: 60, mostly 7940s, some 7912s, a few 7960s.All fiber runs back to main location where it joins the network ...
What is the difference between unified communication and unified messaging.Which one is supported by call manager business edition?
Hello,I need to configure a PRI circuit that will be used for a "tie line" between two sites. The gateway will be h.323 and I have configured regular pri's before, just not for tie line.Is their any special commands I will need to add for the tie lin...
We have a new voice design in the implementation stages.Originally we had:Verizon-->Edge_router-->IP2IP_GW-->Call ManagerThe Edge_router and IP2IP_GW are both 3845s.It was determined that our failover dsign was not working properly and it was suggest...
