Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Running CM 6.1 I have a Hunt Pilot Setup with a couple of Test Phones in the Line Group. I am testing the HLog feature where the phones can login and logout of the huntgroup. There is a couple of settings in the Hunt Pilot where it Can forward no a...
Hello,I have a problem, I want to display on my form the phone's description instead of the SEP address.This is my code : <% var phones = axlquery("listPhoneByDescription", "<searchString>%richard%</searchString>", callManager, callManagerUserId,...
I just got CUCM 6.1 installed. I noticed that from the corporate directory from the phone, when I search for the users, I can't use the "Dial" key to initiate a call once the user is selected. The button is there and I can see it being selected when ...
We are using call handlers to queue people calling into a DDI if busy. If the user isn't busy the caller hears MOH whilst the called phone rings, surely the caller should hear the call progress tones, seeing how the call phone is ringing. MOH plays i...
HiI need to change the connection speed on the router to 1.0gpb from 100mps.Any idea on how?ThanksRobert
Hi all,I have a question here. I'm using Cisco Unified CallManager (CUCM) 5.0.4. I called from ip phone which is register directly to the CUCM. I called a number that have an IVR system. As example an airline company. After my call established, the I...
I configured a service for Meetingplace Express and assigned it to a template in BAT. I pushed the service out to all my phones successfully, however, if I go in through the user options page and try to update the parameters of the service to config...
Hi all,I'm experiencing a problem with CCM Administration. I'm trying to change two Service Parameters ("Auto Pickup Enabled" and "Transfer On-Hook Enabled". When I try to change it and press "Save" button, Administration hangs with the message "Load...
I have a 2851 with ios 12.4(h3) running MGCP. when someone calls the did 1531 they get a fast busy tone. the debugs shows the folliwingFFHQVG01#*Jun 12 16:45:40.729: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x1A54 Bearer Capability ...
Can we can use a IP Phone to act as the TFTP server for the other IP phones in the local office ? (save us bandwidth across the WAN)
Hi,I just had an install where I used Vic4-fxs/did to integrate some polycom phones to ccm using sccp.Howevr I am experiencing a one way voice on them.I have searched the whole forum for similar problems, but havent found any such thing.Any ideas wil...
Just finished installing a new callmanager 6.1.2, i have 2 issues. Busy lamp status for call lists. i have set up the parameters and have all people in a presense group. When a user geta missed call the busy lamp status on the calls list are not bein...
Hi,I want to configure redundant TFTP config for IP Phones.But on the CCM/DHCP server, how can add two TFTP entries in the same DHCP scope.It allows me only to modify the TFTP address in the scope but not add another.Can somebosy advise how this woul...
we have callmanager 6.1 with mobile connect currently when i try to hand off from my cell to my desk phone it gives a fast busythis only occurs with at&t... all other providers work has anyone see this issue
Hey All - I am in the midst of a UC 6.1 upgrade that has been a bit of a challenge. However, I was asked by the customer today to make an additional change that I am a little stumped about: They have an existing CallManager 3.3.3 2-server cluster, ...
