Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hiwe have CUCM 11.5 and UCCX 11.6 and recently added new CUBE in our topology. Some of our incoming calls confront with DTMF problem. We have set DTMF command under our dial peer configuration, but still we have problem.We have 2 SIP Trunks that one ...
Hi Team, Please let me know is there an update to do Call recording for Cisco ATA 190 & 191, when it is connected to CUCM and CME.1. How to do Call recording if Cisco ATA is connected to CUCM ?2. How to do Call recording if Cisco ATA is connected to ...
Hi allI have a cisco 2811 router with pvdm2-32 and vwic2- 4FX0 and IOS version of Router is 15.01 when I use this router as a fxo gateway : in outgoing calls , the Co line is occupying but no connection to called number is happening , just some ...
Greetings - As part of an in-progress CUCM 12.5 setup, I've setup and run LDAP synchronization with our AD.I'd like to know how I can undo the LDAP synch and start over from scratch. I believe I can delete the existing search bases (I'm using eight),...
Good morning - We just recently started receiving this error a couple of days ago. Nothing in the environment changed, but the directory simply stopped working. What is even more odd is that my phone (8865) could browse the directory yesterday but it...
Dears,i have a below UCS M3 server BOQ in which it has E5-2643 CPU running 11.5 version of CUCM,, hence the supported hardware link only shows M5 hardware, this server was purchased for 9.1 and it has been upgraded to 11.5 since from past 1 year i d...
When creating a new phone in CUCM 11.5, I would like the line setting for Forwarded Call Information Display on Device to automatically be set to Caller Name and Dialed Number. Does anyone know where this setting can be done so it will apply to any...
hello guysNeed some help here asap!!!!i m running 8.6.2-29000 cucm manager clusterall my mgcp gateway and sip trunks incoming calls configured with "Inbound Css" with filterto block/allow/Add 9 prefix and more.i facing the issue with 'anonymous' ...
We are trying to re-flash the boot rom / firmware for 7821 phones without having callback manager.We need to obtain the XMLDefault.cnf.xml file to adjust the specifics of the version for the 7821 phones that we have.Is there a way to get this file so...
Hi, Do we have any configuration in Cisco, which allows the internal calls between two IP phones to be routed via Cisco voice gateways. In Avaya we have the feature called Hair pinning and if it disabled, the internal calls between IP phones are rout...
Good Morning, We have locations that can enable or disable holiday mode from a hard phone when needed. Recently one location standards pin is prompting locked out. All users call into the direct line and go through the same steps. Can someone plea...
Hi All, I am figuring out which phones I will need to decomission and what I can keep online if I am planning on moving off of 11.0 to 12.5. I have read that 7912s will no longer be supported current-post 11.5, does this apply for 7912G (if there is ...
Hello, dear support community. I get used to configure separate inbound and outbound dial-peers. GW is connected to more the one CUCMs. 1. I would like to find out if a bind command works for incoming dial-peers ? ( I would like to separate dial-pe...
Hello We have cisco BE6k appliance running trial licenses now, I have been quoted for our CUCM 11.5 for 100x 8811 IP phones with the following 2 Licenses : Option1: 100x - BE6K-UCL-ENH Option2: 100x - LIC-CUCM-11X-ENH-A The supplier said they h...
Hi all, I configured a CTI route point with a DN used for an on-call number for the team. But i do not know how to associate it to Self Care Portal to configure call forwarding. Any suggestion? Any advice would be appreciated.
