Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Can someone please explain what do you get with just the UCK9 license ? UCK9 : AdvUCSuiteK9: uck9, cme-srst, cube Currently I have a 4331 (IOS XE 16.09.04, not on smart license) that I am using for data and want to use it as a CUBE, do not need CME ...
Hello all,I have problem with Cisco IP Communicator 8.6.3.0 I changed my laptop and I changed the mac address on Communicator but it didn't work and I got message on the display "Configuring IP"Please support
I am unable to connect the routers to the internet. I have the cisco Ip phones 7945s and the 7841s. I have the firmware needed for the phones on my pacstar 447 routers, I have each type of phone in its own folder in my voip folder on the router. I h...
Dear AllI have Cisco CP 3905 phone in our office. I just want to know that it support 3pcc Firmware or not ?Please confirm. I want to register this phone with another vendor IPPBX .Is it possible or not ?
I have Cisco Unity 11.5 configured via sip to a CUCM v14. I have configured voicemail and everything works as expected except for one thing, when users press voicemail on their phone there is a long pause (10 seconds) before Unity will start playing ...
My Finesse profile doesn't have a phone directory - my co worker and CCX customers do. I was able to add/delete contacts for their group directories, I know now that the changes didn't take effect until they log off/on again.I tried various CCX setti...
Hi guys, I have a trouble with my CME, with FOX card, I've configured custome-cptone on voice-port FXO, but when I disconect call from PSTN, the call is not disconnected in my softphone.PSTN --------------------- CME ------------------------- (plar) ...
After Agent answers an ACD call, attempts a Direct Transfer to an invalid extension.Finesse produces the following error and takes about 10 seconds to return back to the active call. UCCE 12.5.1.10000-24 ES08 Error: Cannot Perform Operation. ...
I have a JTAPI application that needs to record the called party's DID numbers for the Incoming Calls. Incoming Calls to 11 digit DID over SIP trunk get directed to an internal 4 digit DN on a CTI Routepoint via Translation pattern with Called Party ...
Hello, We are having an issue with only certain numbers. The number is dialed then you hear maybe half a ring then silence. The calls stays connected but no audio and I see sender packets going out but no receiver packets. the calls flow is as fol...
Does someone knows if CUCM register's 8875 will have cloud meetings (using webex edge or other way)? It is odd that when register on cloud does have this capacity but on prem does not.. Thanks!
Hey Community I have an interesting scenario 3 phones 8845/8875/Jabber Mobile sharing the same number (share line). If busy trigger is set to 1 on any of those lines-phones (appearance) : an external incoming call does not ring on that appearance BU...
Hi,I am setting up the Soalrwinds VNQM module to monitor the Sip trunk status of Cube using SNMP. I enabled the keepalive on the dial-peers and see the trunk status "up" for some sip trunks and "unknown" for other dial-peers in SolarWinds. The sample...
Dears, I am aiming to buy a new phone system for 50 users (50 phones), 02 trunk sip (30 channels + 99 SDA from TN + 50 SDA from FR) So I am aiming to have the new C8200L-1N-4T with 2 port Multiflex Trunk Voice/Clear-channel Data T1/E1 Module. Can yo...
Hello. We are currently using Unity Connection 12.5. Per Cisco documentation, only 1800 users can use Single Inbox per Unified Messaging service configured. In order to provide a user with the ability to use Single Inbox, you must give them permissio...
