Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I've recently downloaded CE Console 8.1 and I don't see any associated release notes that tell me what has changed from CE Console 8.0.The feature I'm hoping has been added is the ability to send the Audio of Mic Input 1 (podium) to the room ceiling ...
Hello All, I would like to know if there is away to transfer currently stored voice mail to different Ext. I know I can add an alternate extension, reset the password and provide access to the voice mail, but what I am looking for is to have the curr...
Hi Guys, We have been following the instructions on how to pair wireless microphones with a Cisco 8831 CP however we have had no luck. when we go to pair, we hold the microphone down until the red light is solid and then release, at which point not...
I have a decent amount of experience in coding and scripting. What are the ways I can manipulate Cisco IP Phones remotely? I'd like to do the following things (for example): change Alternate TFTP of a large number of phone (some are remote MRA)co...
I have a VG224 FXS ports registered as MGCP in CUCM 9.1. All the ports are showing registered in CUCM. But Some of the ports have no dial-tone or ring. I tried re-configuring the ports , resetting and even tried rebooting the VG224 itself , but noth...
I have a 8831 conference phone that takes what seems like way to long to register. I just timed it with the stop watch on phone and it took about 6:17 minutes to register. I've done a hardware reset of the phone. It's causing frustration and confusio...
Hi All, Unity version = 10.5 I would like to use the tool "User Data Dump", but I have to start the proxy service. When I go to the documentation for this version, it gives some steps that can not find it. seems like those steps are for version 8.x. ...
Hi there, Went to connect a 6921 phone and nothing was happening. Power inline was set to auto, and it was showing as on when the phone was connected, but the phone wasn't powering up. Moved it to another port and it came up. Having a look at the...
We have CP-7841 phones and ordered new heqadset to use with them. The Plantronics HW251N headsets were ordered with U10 adapters which did not work. Ordering A10 adapters yielded the same result. Both have a slight high pitch sound when pressing t...
Dear all, I am already prepared for my ICND2 but I was wondering if there is any chance to build a simple VOIP topology at home? I was thinking of router, 2switches, 2 cisco phones. Can it be done without using CUCME? I was looking online but there...
I'm having a strange issue. Calls to my Unity Pilot number are slow to pickup when dialed from a SIP phone (88xx, Jabber), It can take Unity up to 10 seconds to answer. Dial the same pilot from a SCCP phone, and unity pickups instantly. Unity is ...
Hello all,I've read many post in this forum, and not found yet a way to prioritize the G711-A in the CUCM (6 or 8).By default the CUCM use the G711U, and IP Phones also. All solution have to use a Transcoder even just interverting a codec :-(Is there...
I have a customer requirement for a hunt group that during opening hours will be in operation and also if a call is unanswered it will go through to voicemail (rather than queue calls). During closed hours the voicemail needs to be disabled and just ...
Hi I got one user physical phone, there is envelope blinking even though there is no voicemail for that particular user. How can I overcome this ?
Hello, dear support team. This is a jabber calling -> CUCM 11.5su3 -> SIP-> 2921 154-3.M -> E1 -> PSTN to Cell Phone. MTP are registered at the old CUCM I migrated from. However, I have checked - they are not used during calls (only for E1 time-slots...
| User | Count |
|---|---|
| 6 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
