Other Collaboration Subjects

When installing Customer Directory with CM v4.0(1), I used Custom option to generate LDIF files. Now I want to import the data from the LDIF files to AD servers. How can I do this? Or I can only use the "ldapmodify.exe" in CM servers to do so?Thanks.

Customer has 4 7940? phones each with dual sidecars. Each line on the sidecar is a shared line that is set up to flash only when calls are in progress. If there is a call in progress on one of the extensions on the sidecar, the main line on the phone...

I'm not looking for an exact answer, just some direction on what may have occurred.We're running CCM 3.3(4) / Unity 4.0(3). One of my users just told me that she just received a voicemail of a phone conversation she had about a month ago. The conve...

Is it possible to have one CallManager cluster use gateways registered to another CallManager cluster to make calls to the PSTN? For example, I have one cluster with two gateways to the PSTN. We're starting a new cluster in the same site for a clea...

Hi guys:What is this command here for? Which case we will use music-on-hold from the router for mgcp? I know usually we get music-oh-hold from ccm and also can configure router to use music-on-hold in SRST mode if issue moh music-on-hold.au under cal...

I have a soft phone and it works great; however, I can't get to the corportate directory. I can access the directory through the Cisco 7940 phone on my desk. The soft phone documentation shows how to add a directory through LDAP; is there some servic...

Will IP Phone 7936 supports softkey "pickup". From doc, it says "yes". But I cannot configure it thr. nor found this key on the IPhone. I am using CCM 4.1Pls help, thanks

We have our 'Tone on Hold Setting' in CCM 3.3(4) set to Zero seconds. For internal calls between IP phones there is one set of on-hold beeps when call is placed on hold. Calls that come in over PSTN on IOS H.323 gateways (on 7200 routers) - get tone ...

I have a sysem where the second call into the AC rings only for a couple of seconds and then goes to voice mail.I have another client where I can set the ring duration on the DN. Both have the same version on CCM.I suspect that there is a service par...

Hello,When a first incoming call rings and I take it, I can transfer it to another extension. However when a second call arrives before the 1rst call is transfered, the phone highlight this new call automatically and the only available option is to a...

Anyone can tell me the current limit for the number of controlled device (CTI port and RP, phone, etc..) for single application provider (in other word for each Jtapi user) ? I know the total limit for single CM or cluster CM but the number I'm reque...

I am on Call Manager 3.3.4 and BARS 4.0.2 and periodically when I check the BARS backup logs the scheduler looks like it will start, but it will only erase the old log file and then the backup will not run. In the past I have gone in and just re-ena...

Hello,I´m having a CCM3.3.4 with several Hardphones and IP Communicator running.The problem is only with the IP-Communicators.During outbound Calls after a few minutes the caller on the IP-Comm couldn´t be heard on the PSTN-Site for several seconds a...

Hi All,Can anyone give me an appreciative max number of calls that can be sent through 3640 router?Our 3640, connected to Avaya via E1 (only one E1), jumps up to 45-50% CPU util when we send 17 calls using GSMFR codec.Voice card is configured with co...

We have Call Manager 3.3(2) and a MGCP gateway with one PRI to PSTN and other PRI connecting to a PBX using Q.Sig. The problem is when a PBX phone places a call to an international mobile number, the PSTN takes a lot of time to process the call and a...