Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello, We have a new site where we are planning on installing brand new WAP units (CW9166I-B) and C9800 WLC. This is a green field deployment. Our wireless vendor is telling us that the CW9166I-B units are Meraki Cloud and not Cisco when you first i...
How can I block a device on Meraki Access point?
I have several 9120AXI AP's that I am trying to get to join up to the WLC. I have others working fine at the moment but these latest few only find and connect up when connected to the same switch as the WLC. Management VLAN for the WLC is 50, I trunk...
Hi all,I am experiencing an issue with 2x C9120AXI access points.They are reloading every few hours with no time patternsThey are displaying a "power Imax error detected" error message on the switch (see below)They are connected to a C9300-48U switch...
Two WLC 9800 N+1.Enable AP Tag Persistency is enabled on both controllersIf I set a Policy Tag on an AP and write the tags to the AP when it is joined to WLC 1, and it then joins WLC 2 it will keep the tag setting. If I then set another tag on the AP...
Interesting antenna connectionsI saw this picture on linked in and thought it was interesting...The way the antennas are connected is not the way I would have done it. Each antenna has 1 x 2.4 and 5 Ghz radio connected. I was trying to visualize...
Resolved! Both SSIDs is not showing in wifi
Dear,we have facing some issues related Wifi ssid we have two ssid configured in our controller wifi-guest(vlan1008) or wifi-User(vlan1009), but still showing Wifi-guest & proper internet working. so guide about second ssid.Regards,Muhammad Sufiyan
The 9800 wireless controller failed to classify devices, causing the wireless air interface scheduling optimization to fail. 9800CL#show install summary [ Chassis 1/R0 ] Installed Package(s) Information: State (St): I - Inactive, U - Activated & Unc...
Hello, Everyone.I was recently browsing through the internet in search of a new fast AP that is able to wirelessly bridge to my non-cisco wireless network and I began reading about the features of the Catalyst 9130 AP. Then I came accross this docume...
Resolved! 9130 AP, New out of Box, Jumble CLI
I have a recently received RMA replacement, new out of the box 9130When I try to console in, I see this jumbled textI am using COM3, 9600 and I just done working with 7 other APs the same way which were perfectly fine. I tried the reset button, etc.T...
i introduce anchor controller in network for guest traffic this anchor placed in DMZ - modle C9800 Foreign Controller is already placed in Data center for User traffic. i understand Mobility tunnel and capwap tunnel sever different purpose on diffe...
AP 2800/3800/4800/1560/IW 6300 gets into a loop after attempting to join WLC with FIPS enabledIt dosnt work for us to reset the AP. Still looping. We have a lot of 2800, only one happen so far. Is it possible to do anything else?
Hello Communityi've amazing misbehavour with scenario where i need to restrict vast majority of clients of locally switched SSID toward sensitive subnet while allowing specific clients to access this subnet. for this to work i've configured ACL denyi...
I have a Cisco 2602i that will not join a Cisco 5508 WLC.When I watch the AP start up from console I see these messages:*Jun 13 16:55:09.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller*Jun 13 16:54:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection ...
お世話になっております。C9166をチャネル52/56の40Mhz幅で固定にしている無線APがDFSを受けてダウンしました。40Mhz幅であればFlexDFSが機能する認識ですが、今回のケースは52・56どちらもDFSを検知したせいでFlexDFSが機能出来なかったという認識で合っていますか。
