Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Everyone, Is there any option proceed to user permission and role imlementation with bulk administration tools ? I want to give jabber capable role end user ccm end users role. Thanks,
I am new to Cisco voice and looking for a help on Cisco call manager cluster setup having a publisher & subscriber. I have a Cisco publisher running on MCS 7835 I3 (v8.6) with IP address 10.0.0.1 & recently implemented a Cisco subscriber on VM (v8.6)...
hello all, am new to cme, i need to configure cme without seperate dhcp server. iis it good to configure with static ip heard cme can be configured in 2 way sccp and sip in which case i should go for sip and sccp? is there any reference doc for my ...
Hi All, Route Pattern is not working for a specific AREA-CODE. Could you please help me? I have the following Scenario : Our HQ is San Francisco and there is another branch in LA that we just allow them make outbound calls to area-code 213, but now w...
Hi I have a CUCM 10.5.2.10000-5 and a OpenLDAP in my OpenLDAP I have the user created and working, when I synchronize the CUCM with the OpenLDAP directory only synchronize a few user, and only one user with all parameters, if I review and compre the...
hi i config a pri GW ,the GW connect to CUCM use H323 when i call a pstn phone ,is all right but when i call the internal call from PSTN,i will receive next signaling Mar 17 11:17:10.848: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0F3A ...
Hello, How can I change the port CME is using with UDP packets for SIP signalling? I see that the SIP packet is using source port as 5060, but after it gets encapsulated with UDP, it is using some higher port eg: 58729 and the voice provider seems to...
I have an issue logging in cross cluster with 8961 phones. It works fine with 7945. With the 8961 phones the logout and corporate directory are missing.
i have two phones sharing the same extension with the same partition and CSS , when one of them is in use the other one led doesn't light up , all the other phones are okey except these two , one is 7965 and the other DX650 which have the main line ,...
Hi Experts, I was wondering how to update new list phone book contact list in cucm so that receptionist can look for any user from phone book. I got the request to put new list of contact number in the phonebook for the two reception phones (model ...
I was curious for those using CUCM 10.x how many of you utilize Extension Mobility, and the Self Provisioning Tool and if so do you use it with many sites. I can see the self provisioning tool possibly being an issue as you will need to create quite ...
Hi Experts, We have centrallized cisco infrastructure in place with 10 branches. HQ have SIP trunk and analog lines where all branches have there own gateways and analog lines connected. Now we are going to implement Call recording solution for HQ a...
HI Guys, I have a problem in random call drops internal to external & vice versa CUCM ----H323---SIP-----ITSP follwing log appears in CUBE SIP: Internal Error (INVITE, invalid IE content): IEC=1.1.100.7.35.2 on callID -1 Please advice
Hi, I want to configure SRST on a 2911 voice gateway, but when I try to enter the ip source address, I have the following error message : 'Configured ip address does not match any interface in given VRF. Pls configure a valid ip address' Cisco 2911 ...
I've tried 3 separate 7945 phones this morning and none of them are taking extension mobility 1. On Phone config page I've checked off "extension mobility" 2. I've subscribed to EM for the phone 3. I've added the phone as a controlled device to "User...
