Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Could you please describe me what is difference between CUCM only and CUCM IM & Presence server ? Does CUCM IM & Presence function both CUCM and presence server ?
Hi everyone, I have a VG224 SCCP running IOS 12.4(24)T7 Voice ports use the CPTONE BR ( config below ) and the problem I am facing is that when any analog phone connected to the FXS ports is taken off hook it generates a continuous dial tone ( inste...
Hello, we have discovered a couple numbers that do not ring while the call is connecting from a Cisco VoIP endpoint. The two numbers are 610-328-1500, and 517-827-0273. When we try to call the number, it says "Connecting...", and then after approxima...
Hi, Expert. I have some problem with IP Fax (SIP). I registering IP Fax to CUCM and success registered. But , i can't make a call. I trace to CUCM RTMT i give error message 488 . Please, give me solution. I tried to configure after 1 weeks.
I just started a working with a company and they numerous CIPC devices configured in CUCM but I would say roughly 80% of them show as unknown/unknown. The issue I am having is we are using UCL licensing and each one setup whether it is used or not i...
Hello, currently I try to configure the cisco VoIP solution for a small ofice and I have some problems with SIP registration of the 7821 endpoints. I am using CUCME 10.5 version and the endpoints have 10-1-1SR1-4 firmware. I have checked with platf...
Dear All Kindly i have an issue with enable srst it is not work , we try to enable SRST in router 2901 and router license is License Type: EvalRightToUseLicense State: Active, In UseEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 w...
Hello, I am looking for the confirmation that DSP transcoding ressources on CUBE ISR G2 can be used by the CUCM in a scenario where the same DSPressources can be used as transcoder for the SIP trunk connection to the ISP ( CUBE acts as SBC too). Is ...
I'm configuring my USC system to be able to send voicemails to user mailboxes. I have everything configured correctly on my cisco system, but I can't seem to find directions on my Exchange end. I have a 2013 Exchange server and I don't want to use al...
Hi voice experts, Is it possible to synch CM for directory purposes and not for end users? To clarify, I want to be able to leverage Active Directory for dialing between sites but each site is a separate CM database. I don't want to fully populate e...
Hello, We have two sites having CME both are connected to each other via SIP Trunk. One site (e.g. siteA) is having SCCP phones, other site (e.g. siteB) is having SIP phones. Calls from Site A to Site B are successful, where calls from Site B to Site...
Hi I have a customer that have two CUCM clusters, both running 9.1.1 (long story why it ended up so). One cluster have not enabled "Cisco CTL Provider" or "Cisco Certificate Authority Proxy Function" and the other have not. Why its like this i don't...
CUCM System version: 7.1.3.30000-1.Please someone could help me for the below query.I am getting below RTMT Alret,need to know what is the cause and how do i troubleshoot the case."The following SyslogSeverityMatchFound events generated: SeverityMatc...
Hi Guys I have new different issue ,dont know anyone has faced this before. We have installed around 20 new 7841 phones with CME. According to the admin there ,IP phones when in connected state shows "Provision Mode" on Display and when you disconne...
Hi, we are using CUCM version 10.5.2 and J4W. Is there any way to find out how many users have logged in through Jabber? Secondly,can we forcibly logout Jabber user from Call manager? Please advise. regds, aman
