Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have a client with a few Cisco 7916-24 expansion modules on their 7975 phones. One of the users modules is working fine and lighting up - we can see the users speed dial numbers and watched lines OK. However The other 7975 expansion module is no...
Hi,How do i enable CUBE feature on 1921 router.RegardsKetan
Hello all ,,I have a weird VoIP quality Issue "robotic sound" in our LAN network. it isn't continues nor general because it happens from time to time, in one building and to be more specific one Switch as I was reported that it only occurred on call...
Hi, I have customer running CUCM 5.1 and he recently bought a 6921 ip-phones, I have checked online and I cant find if it supported or not. And cisco is not support me since its End of Support. Please let me know.
Here is my call flowSCCP phone siteA calls an SCCP phone at site B over VPN tunnel. Site B phone has call-forward noan to CUE pilot. This call get disconnected.Also if I try the followingSCCP phone siteA calls an SCCP phone at site B over VPN tunnel...
Hi, I have two 2 PABX on my local network (Astersik&Avaya) and a Cisco 2800 gateway with voice/uc support.I want to connect both PABX with cisco 2800 with sip trunking so that i am able to interconnect both PABX.I have connected Asterisk to csico ...
I have 16 Cisco 7942 phones that I am having issues with. Our setup is that the call manager (and firmware files) are located across a satellite link. What we are experiencing is that our phones can update to 9.1.3 SR1, but when I unplug and replug...
HiI want to configured QoS on my network but I don´t how to identified if the phones of the network mark the paccket woth CoS of DSCP? Is there any tool taht can help with this or a command of teh Switch.All the switch in my network are cisco but the...
Just did an update of (140) 7965 phones, and everything went pretty smooth except for 5 phones that got stuck on a messge showing "Ethernet Disconnected". The users power-cycled the phones the next morning when they came in and everything came back u...
Hi everyone,I already configured my CME router version 10, and I want to use PhonEX one billing server to record and bill external calls.Unfortunately, I couldn't install PhonEX one !!!Have u already tried to use it and please share with me a tutoria...
Having an issue getting a VG204XM gateway to register with CUCM. Status on VG204XM shows error with downloading configuration file. Is this a compatibility issue, where the VG204XM is not supported by the version of CUCM? Please advise. VG204XM IOS v...
Hey All, We applied firmware upgrade to 894x phones and upgraded them from SIP 9.3.2.12 to SIP 9.3.4.17 in our 67 branches. each branches has 6-7 894X phones and Data Line is 2 Mbit or 5 Mbit for each branch The issue is that the upgrad...
Hello, Been working on a Cisco 2811 setup as a UBE device to terminate a few different voice techs (PRI and SIP), and send them via SIP to an IP-PBX. I'm running into problems where the CUBE will immediately disconnect a call when you lift a handset ...
I'll preface this by saying I'm somewhat new to SIP trunks and still learning about the various config options, communication process between endpoints, and deciphering the debug output.We have a pair of Cisco 2951s set up as our CUBE and a pair of S...
Hi, I want Open the Case for RMA but i have the problem for found S/N of Bundle.I don't keep the box of the Phone 8831. I found the S/N of Bundle on CCW but i don't have the correspondence with the S/N Phone. Have you already had this problem ?
