Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
On CUCM 12.5.1 SU3, looks like the setting for Wireless Headset Hookswitch Control on 7800 and 8800 phones has been removed. Is this a feature or a bug, or am I missing something? The setting is available for 7965 phones on 12.5.1 SU3.On previous rel...
Hi,I have got a number from OVH and decided to use a cisco ATA 186 with my analog phone to make and receive calls. I have upgraded to SIP Firmware 3.0.1Here are my SIP parameters :any help GREATLY appreciated!
We have a Cisco CP 7821 that has two lines One of the lines is set to forward to voicemail ("Main Line") Can not seem to make that line active so that the soft keys are functioning for that specific line (so that we can "Fwd Off") When selecting that...
Good day Experts.I have two sites seperated by a WAN that has an MPLS.Site A has the CME and Site B is like a Branch with some Phones. The two have different Subnets.1. Site A phones can register2. Site B phones are stuck in registering mode3. The DH...
Hi everyone, I've got this new vg router to deploy, ISR4321 with 2x NIM-2MFT-T1/E1 & 1x PVDM4-128. At first the router came with pvdm installed on motherboard. but when I try to create E1 pri-group it says no dsp installed. After a while found an ...
Hello , I connect to cisco IP phone 6921 via SSH and try to press the button remotely , I saw that there is a "RTL CLI_PRESS" command that allow me to press the button , after I succeeded to press all the button I saw that I can't press the soft...
Hello, In SRST mode my Jabber Softphone client is correctly registered to my ISR4331. I would like to transfer a call from 2000 to 3000 but the transfer button is grey. The same transfer is OK with a Cisco 7821. In SRST in my voice register configura...
Hi Experts, Can anyone help me out if Voice Quality (MOS parameters, etc..) related data is collected on CUCM (CMR?) from calls taken on following devices:- Third-Party SIP Device (Advanced) - Cisco Webex Wireless Phones 840 and 860 many thanks,Tibor...
Hello, My local jabber is not registering and I realized that Cisco UDS service does not comes up.. only in starting status. Can you guys suggest something? I am following the tshoot link: Troubleshoot Jabber Log in Problems - Cisco Thanks.
I am trying to register a CP-8945 VoiP phone. I have filled in all the information needed and added a line group. The display is showing the information but it's still showing unregistered on the CUCM. I'm not sure what I missed. Please help. Th...
Hi, Greetings, Currently working out with Cisco IP Phone 8851 and 8832 however got stuck with this prompt message. Is there someone here who can help us to go through?
What is the max number of people that CUCM 14 would support on a multiway conference call?
I have a CP-8945 VoiP phone that was previously used. I was able to change all the information for a new End User. I'm able to ping and type in the IP address and it is registered on the CUCM but it still shows "Registration in progress." Any idea...
Hello, it became necessary to turn on call forwarding at the reception area, where all the landline phone calls are being received. When the phone calls are being forwarded to the mobile, all calls arriving at the landline number are being dropped. I...
Hi, What are the firewall required ports for wifi-calling?I've found old article that stated: UDP ports 500, 4500, and TCP 143 ports but not sure if there are all ports that need to be allowedWe have restricted internet breakout for the visitors wlan...
