Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Please if this is in the wrong forum let me know.Customer has purchased 2 BE6000 server sets. I am tasked with implementing them as High Availability.The units are coming with CUCM, Unity Connection, IM/Presence, and Informcast (paging).My ...
I have analogue line connected to FXO port on Cisco 2851 router which is then forwarded to number 9007 on CUCM (H323 connection). On 9007 there is IVR which is redirected to a fixed phone.All incoming calls get disconnected after 2-3 minutes (time f...
I have a problem.I have been an IP comunicator right through a vpn.I can call without any problem to phones that are registered locally and the PSTN.but when I try to dial to another IP that is registered comunicator right through vpn we fail to esta...
I am setting up 2 branch offices in another state. Each office is relatively small, with about 10 users in each. I would like to know the best way to provide phone service to these users. Each site has a VPN back to us for their data but are on th...
Is this the right syntax to set a a Alternate Subject Name in CallManager 10.5 for Tomcat?set web-security CH "Hawaii Department of Boating" Honolulu Hawaii US ton.state.hi.us HI-IT-UC-CM-P.dot.state.hi.us myphone.ton.state.hi.us I am worried about t...
I'm having an issue at one location. Call is received, user presses the Transfer softkey and no dial tone is heard - call transfer doesn't work even if they go ahead and dial digits.Phones and Gateway have been reset.New location, transferred did wor...
Hello We are connecting to a customers switch and they sent us a couple of Avaya 9611g phones to test with. I have a Cisco 6513 switch. I have the vlan configured as the default and voice vlan configured of 157. When I plug the phone in, it only g...
I read CSCur00930 and also Advisory ID: cisco-sa-20140926-bash.It has several versions of CUCM listed as affected, and also some that are unaffected.Can someone tell me whether CUCM version 8.0.3.20000-2 is affected by this bug as I can't find it on ...
hi, I have one h323 gateway connected with CUCM 7.1.5. This gateway has 4 FXO ports all having same configuration. Problem is that when cucm calls outside using port 2, 3, 4 can hear outsider sound but called party cant hear cucm user. This problem i...
Hi,I am using two Cisco devices (C3845 with Version 15.1(2)T2 and C3945E with Version 15.2(4)M6) to handle SIP calls.Calls work fine, but I have a problem when call termination side hangs up a call, my Cisco is modifying Route Header with improper da...
Hello,i'm new to this forum and i hope to get some assistance.We're using CUCM 9.1 and my Boss wants that all callers hear an announcement and music instead of the ringtone.I already tried with call queuing for our hunt-group, but this only works, wh...
Hello everyone,I have to configure a Cisco SIP phone 3905 in CME ver 8.6. I haven't found a way to do this.I tought about doing it with Fast Track (voice register global-type), but it is supported on CME 10 and above.I was thinking about registering ...
I have a requirements for a Call Conference Solution to connect branches around 45 Branches,suggest which conference design suits for this requirements in the scenario of CME/CUCM?
Can anybody clarify me the major difference between the VCS control & expressway?
Dears,I am trying to upload a firmware for 3905 phones in CME 9.1 but i couldn't, also GUI is not working for me I don't know where things are going wrong with me.Attached are the configsThanks
