Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
PABX1->VG1->WAN->CUCM2->VG2=>PRIPABX1 - 3rd party telephony system in Site 1VG1 - old Cisco voice gateway router running as H323 gateway in Site 1WAN - IPVPN link between PABX1 & VG1 in site 1 to CUCM2 &VG2 in site 2CUCM2 - Cisco UC controlling VG2 ...
Dears,I want to know the load files for IP phone 3905 in the router as I am looking for the load file in the router flash but I couldn't locate them, attached is the output for the Dir of the router. Thanks
hello,I have a fleet of 28 000 6921.On a site the pass in 6921 not registered then the internal switch freezes and the PC has no network.The 6921 SIP are firmware 9.3.3.2Some phones take dump bufferSomeone already had these problems?thank you
Hi, When I try to switch call controls to my terminal phone 9951 it is rejected. However models 8945 and 6945 are right. Version CUCM is 8.6 and IP phone are using firmware sip9951.9-4-1-9 ...
Hi,I was looking around the database of CUCM (v8.6), and i have found some gap between the 'phonetamplate' table and the "Phone Button Templates" page. Following items are not shown in the front-end:StandardCN622Standard_Cisco_TelePresence_400Standar...
Greetings! Can anyone tell me is there any tool which can translate a DSP tracebuffer dump file in the readable format?Thanks in advance for your answers.
Hii,I want to make the calls via WAN between 2 locations. The connection is between to CUCM with different nr convention:Site1: 025625xxxxSite2: 0374359xxxPls. check the attachment
Hi all call not going out for some numbers ( Pattern 1******). But in the same pattern calls other numbers are working normal . Phone show connected but no voice or dial tone .How can i troubleshoot this . Thanks
Hi, I have a CUCM 9.1.2 Publisher server who doesn't permit phones register. I tried the recovery disk and after that, the server show the attached message when start and the services seem to be starting but always say "starting" and the GUI becomes ...
Hi...Good afternoon, I have the following question;What happens when you change the IP (different network segment) of the CUCM Publisher that there is a cluster of CUCMs?Are there problems are present? regards
Hello,We had 2 new employees start today, and when trying to setup 2 new 7945 model phones out of the box, we keep getting the error "Load Rejected HC". This would happen after it upgraded some software on the phone, reset, etc. Any help with how t...
Hi voice team, i´d like to know what i need (hardware) to configuring voice encryption on my CUCM 8.6 and Unity Connection 8.6 too. I have two MCS 7816 (CUCM) and MCS 7825 (Unity). Thanks, Thiago
Hi guys! I am trying to develop a configuration where I have Ip desktop phones from Mitel and an Ip wireless Cisco Phones integrated by a SIP-TRUNK. Simple call flowMitel (desktop ip phones) - Sip Trunk - CUCM Version 10.5 (wirless phones such as 79...
we are running CUCM 10.5i noticed that between our phones we can only have 2 concurrent calls before the 3rd person calling the user is sent directly to voice mail. is there a way i can increase that to 4?
We have a gateway connected via MGCP for several FXO ports.We use local configuration for when the gateway cannot connect to the CUCM server.When I configure my dial-peer section I've been placing the FXO ports with "service mgcpapp" at the top of th...
