Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,ITSP have requested we change to inband DTMF (no dtmf-relay) towards them. Have set this up but no longer seem to be able to transport DTMF to LAN side SIP dial peer now. Using G711a codec.This was all working with "dtmf-relay rtp-nte" on ITSP si...
Hello,I have a Cisco CUBE interfaced with a 3rd party PBX via SIP and PRI for PSTN access. If the user on the PBX has a call forward turned on, the PSTN user doesnt hear a ringback. After some analysis it looks like the PBX is not sending a 180 Ringi...
Dear Team,I have a 20 numbers of users with same department, i want to add them in single phone group so that any one got calls from outside. May i know what is best Line group or Hunt Pilot.hari
Hi,I have a weird problem on cisco 7940 that is not registering to outside world. My setup is as below:1. Elastix server on private IP.2. All cisco phones connect with elastix server and gets registered with internal extensions.3. While assigning sip...
I have a working configuration that has two different inbound numbers and one numebr works perfectly both inbound and outbound.not at all But the other numer sometimes works inbound but ALWAYS works outbount.I understand that is is not possable to g...
HiWe have a running CME - CUE system, people can leave and listen voicemail without any problem, but voice message indicator on phones not working. It is always off. CME-CUE config and CCSIP debug are attached . Can you please check and advise.se-10-...
Hi,i am integrating CUCM 9 with Informacast 8.4. i did the basic setup and by registering the default Informacast CTI RP with all the other configurations.however, when i create a new CTI RP to match a new DialCast in Informacast, it doesnt seem to r...
Hi I am having a problem with one cisco 9971 when I recieved a call i heard a short sound..Then the first button on the left turn on (orange/ambar) and at the same time the first button on the right side start blinking and show me in the screen who i...
I have one CSS that's behaving oddly. We require 9 to reach an external line. In my normal device pool/CSS, when I dial 9, I get a dialtone, then I continue with 1800xxxxxxx. However another phone with a different device pool/CSS, I don't hear the...
Hi AllPlease help me to understand the concept of how we can calculate the session while we are configurating the conferencing ang transcoder on Voice gateway.RegardssChaman
I got a 7975G that was interupted during a firmware upgrade. Therefore, the screen is disabled and I cannot see to get it to come back on or upgrade. It will get an ip address from the TFTP but it does not appear to try to download anything from th...
Hello,Company A just bought Company B and both of them have a CUCM integrated with their own AD.In order to "simplify" the administration, Company A wants users of Company B to be registered on CUCM A so there is only 1 CUCM for all of the users.CUCM...
Dear All,We are having some issues on a fresh installation with a Cisco 2911 connected to a remote Call Manager in Denmark. The branch site is in Belgium, when we connect the BRI's to the interfaces we get a "multiple frame established" so all is wel...
I have a customer running UCONN 9, the ELM shows that they need to have 244 speechview users. They do not use unified messaging at all and certainly do not use or need speechview yet there was a temporary speechview piece embedded...
I'm working on an old CUCM 4.1 and I need to use BAT to update the forward settings on several lines. I really don't want to do this one by one. However, I need to forward line one to line two which is the same extension but in different partitions...
