Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a Cisco ATA187 configured. At my desk I have a analog phone connected to it and I can call the extension an the analog device will ring just fine. I take the ATA to a different part of the building on different switches and everything and pl...
We want to upgrade from CCM 4.3(2) to BE6000.Is it possible to upgrade directly from 4.3(2) to BE6000?Someone claims there is a problem upgrading phone firmware from CCM4.3(2) to BE6000. Is this correct?Regards,TorleifTjome Municipality, Norway
Hello there,In the past i wroked with VWIC1 or 2, and i had the habit to uses RJ48 pinout only to bind telco access point to the Cisco's voice card (as wrote down here).Today, i had to play with a VWIC3, and my fellows told me that i don't have to us...
Hi!I have a problem with MGCP gateways - from time to time they cannot receive or send any calls. Then I have to shutdown/no shut E1 controller and then for some time it works OK.Investigating this problem using RTMT PRIChnnelsActive performance moni...
With Edson PineiroWelcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about configuring and troubleshooting Cisco session initiation protocol (SIP) Cisco Unified Border Element (CUBE)/...
Hi All,I'm having a few issues using my SRST Branch Gateway to Multicast Music on Hold. This is when used in conjunction with a Call Manager running 4.2 on a central site. My brnach office Gateway is configured as far as I can tell correctly from r...
himy prob is when i dial my voicemail number is always buzy , so i type this command :CUE# show license allLicense Store: Primary License StorageStoreIndex: 0 Feature: VMIVR-VM-MBX Version: 1.0 License Type: Permanent ...
I have client who has a Desk Phone, as well as Cisco Jabber for windows, iphone and ipad configured for the same extension. On receiving an incoming call all the devices ring simultaneously as designed, but when the call is answered in any device, on...
Keep getting these errors coming through on my shiny new syslog server:-2013-04-12 16:11:48,Local7.Error,voipcucm,13987: : ccm: 2026: VOIP-TDC-UCM-SUB1-011.corp.yw.kelda: Apr 12 2013 15:11:48.584 UTC : %UC_-3-LastOutOfServiceInformation: %[DeviceNam...
Hi,I have installed a new V8.6 cluster as part of a V7 to V8 upgrade. I wanted to test that various phones can register with the new cluster and move them back onto the V7 cluster as a backout.Both 7911 & 7941 phones upgrade their firmware and regist...
Hello All,I have my VG 28xx to have Slips occur in the T1 circuit(only 1 T1 for the site).Below is the controller t1 output.T1 0/0/0 is up. Applique type is Channelized T1 Cablelength is long 0db Description: PRI for Voice No alarms detected. alarm-t...
If I need to police the RTP packet via the MQC as follow:class-map rtpmatch ip dscp efpolicy-map rtpclass rtppolice 64000 8000then under the interfae mode we will the service policy but in the same time I need to use " mls qos trust cos" like the fo...
Callers cannot hear each other on a CP-7937G. The phone registers with the Call Manager. Calls connect but the calling parties cannot hear each other. Has anyone seen this as a quick got ya / symptomatic of a known issue or common scenario? The phone...
Using CUCM v8.6. Customer has 6921 phones using SCCP integration. By default, the lines on these phones come up set to support 2 simoultaneous calls, with the busy trigger set to 1. Reset this isn CUCM from 2/1 to 4/2. Phone settings applied and ...
Dear team,How i can block all outgoing and emergency number after business hours in CUCM 8.6 on branch sites.Emergency number should route to HQ extent ion.Thanks
