IP Telephony and Phones

MeetingPlace 8 - DTMF not passed on External Calls

Hello,MP8 with CUCM8.6Cisco 9951 IP PhonesMGCP GatewaysScenario:Audio meeting in-session.uses TUI to initiate a call out to invite overseas participantdials the number, and the call goes through. Then there is an IVR prompt asking for an auth. code t...

Call Rejection Error

On one of my PRI's we have a few numbers assigned to dial in. One of the assigned numbers is giving us the error "Your call cannot be completed as dialed, please check the number and try again - Zero Zero Four T". All of the other numbers are worki...

CUE ISM-SRE failing trying to do an upgrade from CME

I am having an issue with a new 2951 and a ISM-SRE-300-K9. They were shipped seperately so I added it, and since then I have reseated it as well to verify. It shows up in the show diag, and is configurable/configured, but I cannot session to it, and ...

Monitoring MTP Utilization with SNMP

Hello,i'd like to monitor the MTP Utilization on my CUBE. I thought i could use cdspTotUnusedMtpSess and cdspTotAvailMtpSess. I have 48 channels on the router configured.Dspfarm Profile Configuration Profile ID = 1, Service = MTP, Resource ID = 1 Pro...

UCUM 9 questions

I have trying with much difficulty to gather information about CUCM 9. If anyone can answer these questions, I would be greatly appreciative.One Touch Call Recording - I know this is a new feature and requires a MediaSense server. Does anyone know ...

Resolved! CDR Billing File Modifications

Hello, Setting up a db for cdr data and have a few issues: 1. Is there a way to remove the header and datatype info from the ftp files? I just want the cdr data. 2. Is there a way to customize the file name of the file that is output?3. Is there a wa...

Can´t access to CUE by embedded service engine 0/0

Hi good morning, I am trying to access to CUE in a 2911 ISR with pre loaded software and ISM module and I followed the next sentence from techincal documentation in order to do it: You must perform the configuration steps in this section, even if the...

Resolved! CME FXO getting busy after disconnecting the call

Hi i am having a setup with cme ver 8.6 and 3 fxo lines .some time even all the lines are free also user will not be able to make the call it will give busy tone that time i use to shut and no shut the fxo port it will work .Please help me how to r...

ATA186 fax issue when modem passthrough enabled on PRI gateway

Hello fellow support forum members,Last week I posted an issue I was having where some Verifone chip and pin terminals were failing to negotiate at higher modem speeds. To resolve this, I enabled modem passthrough on our PRI gateway and configured a ...

ATEX Zone 1,21 Wireless IP Phone

Hey all,I have been asked to locate a wireless phone for use with CUCM that is ATEX 1,21 rated. The 7925EX is only rated 2,22.Anyone have a recomendation?Thanks Jerold

Call terminates after 13min exactly when traversing an h323 ICT.

I have an ICT built between my CUCM and a customer of mine and after 13 minutes exactly the call will terminate. On my end (called party) the phone will show that the call dropped completely and the phone is ready to make a new call on the customer ...

Change 8941 8945 wallpaper background image ?

Hi all,How can I change the background image on my 8941 ?Is it possible ?RegardsPhilippe CUVILLIER Cisco Video 8900 http://www.youtube.com/watch?v=zNmiOFXJcwsB2GAAS http://www.youtube.com/watch?v=4OD0Zp9HJ9ghttp://www.youtube.com/w...

Resolved! only send 4 digits to PSTN

Hi,When I place a call to PSTM throught a BRI port, in a CME 8 the telephone try to place that call sending only 4 digits, when I am introducing the digits, in the 4º digits stop and try to send the call.Progress Ind i = 0x8183 - Origination address ...

called party number incomplete

Hi,When I place a call to PSTM throught a BRI port, in a CME 8 the telephone try to place that call sending only 4 digits, when I am introducing the digits, in the 4º digits stop and try to send the call.Progress Ind i = 0x8183 - Origination address ...

2811 CME Help

So my goal is to run I think CME on 2811 with 7975 phones ( i know super vague can provide more details) just on my small home lab which includes some other switches. Would I be able to run just an internal voice network without connecting to any ex...

IP Telephony and Phones

Forum Posts

MeetingPlace 8 - DTMF not passed on External Calls

Call Rejection Error

CUE ISM-SRE failing trying to do an upgrade from CME

Monitoring MTP Utilization with SNMP

UCUM 9 questions

Resolved! CDR Billing File Modifications

Can´t access to CUE by embedded service engine 0/0

Resolved! CME FXO getting busy after disconnecting the call

ATA186 fax issue when modem passthrough enabled on PRI gateway

ATEX Zone 1,21 Wireless IP Phone

Call terminates after 13min exactly when traversing an h323 ICT.

Change 8941 8945 wallpaper background image ?

Resolved! only send 4 digits to PSTN

called party number incomplete

2811 CME Help

Meet and congratulate the February 2023 Spotlight Awardees!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Cisco 8821 No Recent Calls

ATA 191 CPC Settings Missing

Cisco 8851 - Transfering call to another Cisco 8851 - No ringtone

What newer model of Cisco Phones support Single Button Barge feature?

ATA 192 acknowledging with different ptime size

corlist configuration for outgoing calls to restrict international cal

Cisco IP phone unable to dial (787) area code number. CUCM 12.0.1 ver.

phones stopped working on ISR4331-V/K9

Convert Cisco 8841 from Enterprise to MPP as private User

Cisco VOIP 8945 Error 403: Directory Listing Denied Directory listing