Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,The other day we lost voice calls via our SIP Trunks. I have spoken with 3rd Party, although no Root Cause from them. I have some debugs, which seem to point to otherwise and wanted to know if I am reading them correctly.We believe a DNS issue was...
Hi,Is there a way to setup the Cisco Ip Communicator on Call Manager Express? Do I need to download some kind of firmware?I would like to have some setup guide in the case it could be posible.Thanks in advanceRegards
Hi there, I have setup 7962 with one expansion module for a branch office. all user's extension has been configured as SD in the Expansion module. it works fine. Now new receptionist ask for the BLF on the button of Expansion modu...
Hi I installed Cisco Jabber on Samsung Galaxy S3 for CUCME 8.6 ERROR "Please check your Internet Calling Settings and try again. If the problem persists, contact your system administrator" But it is working fine with S2 and other devices . Please h...
cmterm-7911_7906-sccp.9-1-1SR1.zip
"is this okay to remove the phone files from flash which aren't related to my cisco lab setup?"Reason(s): 1-All phones i've are 7961 series. 2-CME 7.0.0.1 which i'm using contains files for 7906-7911,7914,7920,7921,7931,7937,7940-7960,7942-7962,7945-...
There's a question https://supportforums.cisco.com/thread/2157114?tstart=30 where the poster has a problem firmware upgrading a phone. Doing a factory reset (123....) forces the phone to upgrade, but it still has problems.I'm guessing a CME config er...
Hello Folks , we have two trunk one is sip and anther one is pstn , my voice mail is in some third country and that is routed through SIP , now my requirent is if some body call at my extension from PSTN , it should 8-9 ring then disconnect...
Hi All,I just would like to have some expert opinion on the probability of using IVR through Unity Express and then calls should route to Call Manager.For example, If we have a Site with 2800/2900 ISR Router with Unity Express Module NME-CUE and Cisc...
Hi all,I am trying to upgrade the firmware on a 7945. I've done the steps like every other phone type I have, of copying all files to flash, tftp-server flashing them, going to telephony-service and "load 7945 SCCPxyz", but when I reset the phone, it...
In my lab setup have two seperate 1760 CME 4.1 routers serially WAN'd to a 2620XM router using RIP, that has the Unity Express NM-CUE 3.1.1 module in it. The 2620 is just doing the voicemail and routing between the two CME's, no ca...
Hi after upgrading the callmanager from 7.1 to 8.0.3 i found extension mobility not working. I was told i had been hit by bug CSCsy76489 by cisco tac. I cant find any information on this particular bug on the tool kit since its still internal. I wond...
HiI have spent 2 days behind this little issue and still cannot figure out the catch. I have CISCO3825 with IOS c3825-adventerprisek9-mz.151-4.M4.bin and cme-bacd-3.0.0.2. I just need AA and no need for hunt group. here is the config:dial-peer voice ...
Hi All,Is it possible to do fax over IP which topology below?Fax <<>> VG+transcoder <<<<<H323 G729>>>>>> 3rdParty PBX <<>> FaxBR WINAI
Hi,We are facing a problem in our production CUCM 6.After the power shutdown neither the Pub or Sub is doesn't work the Pub is asking for recovery disk "which is not available in our stock".And the Sub is running but I couldn't access the cm administ...
