Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear Team, Am facing an issue related to out going call over SIP Line. I have SIP Trunk configured on our CUCM and the ISP Allowed range of SIP Direct line 7720 to 7730. [30 Extension]When we place the call from the extension number which fall in tha...
Hello, We recently added a CUCM subscriber server to CUCM cluster. The cluster initially had only publisher and this is the first subscriber server. After joining the subscriber server to the cluster we have noticed that all the phones that were in "...
Dear All, We have upgraded CUCM version 11.0 to 12.5.1. Post upgrade CUCM vCPU is mismatch b/w ESXI and CLI.when I log into the CUCM, the CLI displays a different value for vCPU, and show hardware Please advice.Ram.S
We are integrating our CUCM with Expressway and we want to restart tomcat services on CUCM.We have lot of Jabber users with SSO enabled. So, want to make sure, if it is going to affect any users after tomcat restart.I know we can disable SSO, restart...
Hello, Hopefully a simple question but I can't find any good documentation on the use of sip-ua timers with in the CUBE config and wondered if anyone had the answer please. With regards to the following timers sip-ua retry response 3 timers connec...
Hi, Can you please inform that how can i configure conference setup in our Call Manager Express 10.5 We have SCCP & SIP phones and required conference setup Waiting for your earliest replies will be highly appreciated Thank you Sajid
Hello, I wanted to update name and label of the Cisco 7821 as per commands below.voice register dn 9number 7065allow watchname AdamSlabel label AdamS-7065 I have restarted the voice register 9.CCME-01(config)#voice register pool 9CCME-01(config-regis...
Hi, In the last few days I'm having an issue with digit by digit dials - for example: when I press the "speaker" button and then dial (digit by digit), the call will not go out (nothing happens), however when I first press the number (block of numbe...
I have IP Communicator 8.6.2.0 installed on several users pc's. When depressing one of the keypad keys on the keyboard or via mouse input there is only a Mono tone generated and not DTMF. I have been searching but can only seem t...
We have 100+ cases of brand new CISCO 7841 phones and so far two phones in a row the clips on the stand that plugs / clips into the back of the phone break off. The actually locking clips (the things that hold the stand) have broken off.Who else is ...
Over the weekend our main node is refusing to start its database. We have restarted the and started the service and it goes in a loop for a while then stops and says it's still stopped. We have rebooted the server also with no success still. I have s...
Hi Pals,We were discussing today about how much bandwidth we need to allocate per call or per connection to incoming and outgoing voice. SD-WAN has for some reason degradated the quality of the normal voice operation compared against the MPLS or Metr...
Because of the latest vulnerabilities issues reported for Solarwinds, I am looking for a recommendation to replace Solarwinds as the STFP server used for backups. What other Free SFTP applications do you know to be stable for Cisco? Thank you so much...
Having a problem getting thru a firewall.the phone is sending to two messages in the same packetfirst is a SIP 200 OKthe seconds is a Notiftybut the firewall keeps pulling the second message out and just sending the 1st message. Is there anyway to fo...
I'm attempting to set up a new 8865 phone with one 28 button KEM (dual screen). The phone says it is unable to power the accessory.The phone is connected to a Cisco SG350-48MP. BWE-SW-02(config-if)#do show power inline gi1/0/25Interface Admin Oper P...
