Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I ran ServerUpdatesWizard-v.3.0.13-02-2011.exe then ran CiscoUnityConnection1.2.1-LE24ports and got the error below; Must fix: This version of Cisco Unity Connection requires Server Updates Wizard (SUW) version 1.0.1.0 or later. The current version i...
I am currently running CUCM version 6.1.5.13033-1. I have two Cisco 7960 phones, phone A and phone B.I have a call forward all on phone A to point to phone B. The call forwarding works fine. If phone B doesn't answer the call, the call goes to phone ...
We have some problems with the call disconnection on a FXO ports in CCME 7.1 environment. We have a 2N Analog-GSM gateway attached to a FXO port, and the CCME did not recognise the disconnect tone, so the call was never disconnect (you had to end the...
Hey guys,do you know how I can force a cisco IP phone to restart remotely, even it is in current call? A normal reset/restart waits until the user hang off.Thanks & Cheers,
I have a 7961 with three ??? in the lower left hand side of the display that will not go away - anyone seen this before??Thanks Jim
Hi Deras,I tried to factory reset 7911 ip phone.after that is got worng.It cant boot well it got stuck with cisco logo.I face 2 phones with same problem.what i can recover from the same.Midhun KM
Hi to alli am not sure if here is the correct place to ask thisBelow is the diagramThe ISP will provide a SIP trunk with their router(2811)(see diagram below)Then we will connect with crossover E1 cable the 2811(ISP Router) with customer router(2801)...
Hi NetPro.Good Day . Appreciate if you could share with me about the Cisco CallManager v3 - v4 licenses are purchase individually ? or come with bundled set ?IF CM 3 and CM4 is counting on individually what about CM5 and above ?Your reply will be hig...
I just got an ISR setup with the latest code to do some testing with 9951 phones. I setup everything CLI to start with, but went into he CCME GUI to to do some more work. I don't see the phones or users or anything in the GUI.I called into TAC and wa...
We have a vg204 configured as a sccp gateway with 1 sccp analog phone configured. The corresponding fxs port is connected to a Valcom paging system. When a buttset is directly connected to the Valcom device, we get a second dialtone as expected and...
Hello Every one.I have a question. My customer wants to use his company certificate in cisco call managers and unity for authentication.It is possible to do that and wich would be the procedure for that.Thank you for your help
I have a customer who wants to implement Cisco Callmanager 8.5Main Site: Two Servers, PUB, SUBDR Site: One Server, SUBTotal three serversNo.of IP Phones: 3000 (Normal office users) 50 (Executives, VP's), 50 (Conference Room Phones, Lobby Phones)Total...
I currently have a production v7.1.3 HA environment that I'm preparing to upgrade to 8.5.I wanted to run v8.5 under VMWare (with what has been an unlicensed 10 user version with prior releases), but I'm having an issue with having the option to selec...
Hi,I have a lot of end-users in our Cisco Unified Communication Manager 7.x installation, but many of them are leftovers from the older CUCM installation that we upgraded from.Is there any way that I can see when a given end-user was created in the C...
Upgrading from CUCM 7.1.3.32900-4to CUCM 7.1.5.32900-2two hours into the process, I received this message in status windowThe application has lost communication with the system. Check the status using CLI.When I entered commandutils system upgrade s...
