Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have an XML phone service for a menu that shows public announcement options/extensions that can be dialed. When you bring up the menu, each line item has "Offline" written below it. Is there a way to hide that or at least a simple way to get it to...
I have many cp-6945 and cp-9971 phones.The pushing of # at boot, and then typing 123456789*0# method works for cp-6945 but not for cp-9971.There's a CP-9971 phone, which works fine but has it's display divided to two, so nothing can be read, or video...
Bit of a newbie question. We’re trying to set-up 2 CP.7841 phones with the Call Manager on a Cisco 4431 router. The phones are not registering on the router. The router version is 16.9. The phone’s original firmware version was SIP78xx.12-0-1-11. We...
7911 factory reset fails.RED LED does not blink even if # is held down for several minutes.Is there a good way??
Hello team, quick question about upgrading the SX10 / SX20 systems. I see in the logs that those systems try to request the following loads:SX10: ce9_13_0-990355df13aSX20: ce9_13_0-990355df13a.pkg The phone gets a 404 (not found) from the TFTP server...
Hello, I'm trying to figure out how to properly configure my 8841s with a shared line. I'm trying to follow the admin guide and I am getting stuck. I am using freepbx for call control. I've got it configured to allow the extension to register multipl...
Hi Guys,we got one Problem with our SIP environment. We have connected an anynode sbc to the cucm to connect to a sip trunk. this works all fine with incoming and outgoing call. today i tried the following szenario.I got an internal call an place thi...
Greetings - I'm involved in administering a CUCM 12.5 implementation which is in the (slow) roll-out phase. The Publisher and a Subscriber have been installed at this point.We are going to use an existing Microsoft CA rather than the self-signed cer...
I just installed a combined network locale in cucm, just to test different tones on different country. Now I want to remove it, is there a way to do so? Or it cannot be removed once installed?
Hi,I'm using QM 9 network recording. When I want to play file didn't upload yet, some file can play by showing message "download on demand please wait while the audio file is requested", some file cannot and show more message " PLYR2101 Download ...
Hello, Should i be considering any extra or hidden cube licencing costs formigrating to a 161 channel sip circuit from an existing PRI in terms of mygateways? thanks
Hi all, I have an analog/SIP voice GW(Patton) with FXO port connected to public land line.On this analog GW, I have also analog sets connected to FXS ports.This GW is sip-connected to CUCM 12.5.1: on which I have hundreds of SIP phones Questions: 1°...
Hi AllWe are having issues with our SIP trunk between our CUCM v11.5 and a Mitel phone system.If we call them from older SCCP phones, the call works fine, however when we call them from our SIP 7841 phones we get no audio.When I look at the packet ca...
I can only advice you all to fully test this thing before buying one.- Dial plan not working- Dial plan not supporting "+" and also not "."- Not well documentaed (where is dial plan documentaded?)- Completely different (web)interface compared to know...
I am trying to create a silent ringtone (no music) for cisco ip phones based on the specs given below. What is happening is the phone accepts the raw file (from the edited distinctive ring list). For every ring, there seems to be a clicking sound. Is...
