Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello folks,I have upgraded CUCM 4.1(3) to CUCM 6.0. But Cisco CallManager service is not running, though it is activated.I have not uploaded the phones and node licenses yet. Would Cisco CallManager service not run without license or it is a differe...
Hi I have been asked by my company to set up a phone system after 2 days of playing with it. Suprisingly most of it is working but I don't seem to be able to get any outgoing or incoming calls. I have got closer with debugging but now seem to have hi...
Hi all,I have a question concerning a sort of "least cost routing"...I use the callmanager in version 4.2(3)sr3.There is a connection to our PSTN by a Cisco 2811 router which is configured to act as a MGCP gateway. We use a route pattern 0.! to let ...
I have about 15 different fax machines connected to a VG224 (various models). For some reason only the Brother 3800 models can not send (but they can receive). The VG224 is configured with MGCP and the PSTN gateway is running H323. I've tried settin...
Hello,Anyone can help me understand if it is possible and how to configure the CME SIP to pass DTMF digits via Inband RFC2833 instead of Notify Message ?I have CME version 12.4Thank you very much!
Hi all,how can i configure the AX5350XM as MGCP on the CCM4.2 im not able to fine it on the list ??!?please advice hasan
Hi,Is there a good reference available on how to configure call transfer during voicemail prompt.What I'd like to do is if a call to an extension is unanswered and goes to VM, that the prompt says something like: "Press 1 to be transferred to my mobi...
Hi, We have a scenario where we have a gateway (cisco 2821 with fxo ports) which we have configured in Cisco Call Manager Ver 4.3(1) as a H.323 gateway. We have Cisco CRS application running the icd.aef script. We are able to hear the IVR prompts if ...
I am looking at the Cisco supported hardware page and noticed the following server "HP DL320-G5 Server with Intel 3050 Xeon 2.13-GHz Processor" does not require a hardware RAID controller. Is this correct? Does 2000.4.5 or CUCM 6.x support softwa...
Hi experts,We received this notification from RTMT:Cisco At 10:21:14 on 02/09/2008 on node x.x.x.x.Service status is DOWN .The following service(s) are down: Cisco Serviceability Reporter.Also all of our registered gateways and Media devices were aff...
I have a remote branch that has a call centre (and soon a Call Manager). To reduce costs I want to connect it to an IPCC Enterprise. This is located in a different country via an E3. Rather naively I thought the only costs I would incur would be l...
We have the following problemThe network infrastructure is as follows 6513 Core (Cat OS) - contains 3 vlans - namly 200, 202, 203 The commands used here - monitor session 1 source vlan 200, 202, 203 multicast disablemonitor session 1 destination rsp...
Anyone know or remember when installing CUCM 5 or 6 if it accepts capital letters or small case or a combination when entering in the hostname?Thanks!
Hi,I have a 2851 with 2 VIC2-2BRI-NT/TE. I configured trunk groups to rollover between the 4 voice ports for outbound calls. Everything works fine with all the ports connected (I can place and receive many calls at the same time). Then I disconnec...
So, this method doesn't work on the older firmware. i tried and doesn't respond.http://cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00800941bb.shtmlhow can i get these set to factory default?no CM setup locally.i do have 2821 rou...
