Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I use Callmanager 6.0 with Cisco2801 gw and terminate an 8-channel E1. We can receive calls from PSTN. However we can not make calls to outside ISDN cause code 44 requested/circuit/channel not available. Also the other end rings once and it stops....
Hi, I've recently bought a nice new 7941G phone I need to change the ios from sccp to SIP to make call through the VOIP to connect the sip provider.how i can do the chnages in IOS.
Hi,I'm setting up IPMA in proxy line configuration mode and am facing 2 problems.The first one is that when the manager presses to the transfer to voicemail button when he is receiving a call, the call is not transferred to his voicemail box but the ...
HiHave a 3 server cluster running 5.1(3).Appears the 2 subscribers are not replicating to their local databases. The environment works fine otherwise because the publisher database is referred to first and connectivity to the publisher database is fi...
I have just upgraded my cisco ios to 12.4(15T) but my cme-gui files are still on the router's flash. If I just extract the new cme-gui tar files into flash will it automatically overwrite the old gui files or should i take another approach, such as ...
Current configuration is CCM6 using SIP trunk to Exchange 2007, do you know if there are any considerations y i update Exchange 2007 to SP1? Do i need to make configuration changes?Regards.
I'm planning an upgrade from CM 4.1 to 6.0. I've been reading thru the Upgrade Guides, etc. but I'd like to know what other things I should do before the upgrade. This is a very drastic upgrade as the Upgrade guide indicates "your hard drive will b...
Where do you subscribe your phones and dev profiles to the Login service like you did in 4.1 in the Admin page?
I have a customer who has a Analog phone shared with her IP Phone and when she answers the Analog phone she was wondering how to transfer that call to another extension. So I was researching this and could not find anything. They have a CCM 6.x I ...
I'd like to do the following:Disable the speakerDisable the PC portLock out the menu settingsI'm running CME 4.1 on a Cisco 2811 router, and running SIP P0S3-08-7-00 on the Cisco 7940 phones. I was able to get this working on the Cisco 7941 phones...
Hello, we are trying to split up administration among 3-4 team members of some basic CM duties, such as creatw/modify/delet phones, extensions, and users. I have added the same roles and assigned the same groups that ccmadministrator has but when I l...
Hello there,I just recently upgraded a customer from 3.3 to 4.1(3). They have a lot of 7905/7912 phones.In Call manager 3.3 you could change the settings for the MWI and ringing on the lines of the 7905/7912 phones.In call manager 4.1(3) you cannot....
I have a customer who has a small NOC, 8-10 users. Today they have a Nortel PBX and use MCR keys to answer calls(same number on all phones. Call comes in and is answered, next call rings all idle phones.) They have Symposium call center today and ...
Hello, I am trying to figure out how the voice mail codes actually work in CM 4.2. I have a code set to turn MWI on and a code to turn it off. How do these work? If I dial the codes from my phone it turns MWI on or off (depending on the code used). W...
Hi,our ccm cluster has dedicated tftp, publisher. If I have to install the devicepack to ugprade the firmware, which server should I install? i am assuming that's the tftp server only, right? Thanks
