Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a SIP trunk in India with TATA which I cannot get registered and the provider is of no help. The relevant config is here: sip-uacredentials number XXXXXXXXXXXXXX username XXXXXXXXXXXXXX password 7 YYYY realm SIP-XXXXXXXXXXXXXXauthentication u...
Does anyone know whether it's possible to program a softkey on an 8800 series 3pcc phone to do some HTTP action, e.g. send a POST, GET, or PATCH request? Or, to show an XML application where a user could initiate such an action? We're trying to set u...
Cisco 1760:C1700 Software (C1700-SV8Y7-M), Version 12.3(4)XG1VIC Slot 2:Dual FXO Voice Interface CardHardware revision 1.1 Board revision P0Serial number 0030977039 Part number 800-02495-01"caller-id" command is not available on voice-port configurat...
Hello,I have 2 routers C8200 with CUBE license working as a redundancy pair (main/standby) to manage SIP calls.The routers are working fine but when one of them crashes then the router reloads automatically, i know that enabling no redundancy-reload ...
I use Webex Calling and integrate CSR 1000v(Azure) as Local Gateway Webex Calling > CSRv1000 > ITSP CSRv1000 / privacy ip-10.0.0.4 / public ip-20.59.121.X CSRv1000 Public IP：20.59.121.172 / CSRv1000 privacy IP：10.0.0.4ITSP IP：211.75.165.204 Webex Cal...
Hello, I have to integrate an Ascom IP-Dect in the CUCM infrastructure. I read I need an COP file to import in the CUCM in order to add an Ascom IP-Dect in the platform. Did anybody knows were can I find this COP file? Is it available some-ware to b...
I set up a two FXO ports trunk group (old cisco 1760) with priority on first port.It works, but if I detach PSTN from first port (line failure) , the call is still routed via that port.Is it possible to make system aware of failure in order to use th...
Call Flow: Third Party SIP device registered to CUCM > CUBE for outbound call, below is the invite and then the 422 session timer too small. CUCM min-se value is set to default 1800, and looks like 2000 is expected. CUBE is set to 2000 under voice s...
Call Flow: Saas Solution > CUBE > SME > CUCM > PSTN GatewayWhen a call is initiated from the Saas product, the called party rings and answers, but only gets dead air and calling party still hears ring back.in the attached image, you'll see 19:51:06 i...
Hi Guys, Please find the attached snaps. For International calls we are getting Timeout and S4B (skyp for business) is terminating this call. If we compare the call scenario for local calls we are getting 183 from Cisco after trying, while for Inte...
We are setting up CISCO VOIP Phone CP-8845 together with Yeastar S300 (IPBX Server) + Fanvil X3S Pro IP Phone.Yeastar and Fanvil set up and all IPBX features are functioning. When CP-8845 Powered up, it shown a prompt message to key in Activation ...
Hello community. I have a curious case of a Cisco CP 8845 phone that suddenly stopped working properly.What it does:The phone does power up when connected via ethernet (no, I don't have a psu).It tries to boot, lights next to the display light up unt...
I have a problem with a Cisco Telephone - which is setting the clock. When I activate a new phone, the clock needs to be set, and this option is not available in the settings of the Telephone. So I have to restart the switch. Is there a permanent way...
Good morning, I have a problem on cisco CP-6851-3PW-CE-K9, when I get an external call (lost, received, rejected) does not give me the opportunity to call back the number. If the same number is typed (without +39 in front) there are no problems.Is th...
Some of our IP phones are located in bedrooms and at night when the phone goes into power-save mode, the select button LED lights up. It is bright enough to light up the room and cause people to complain. Is there any way to disable this LED from ill...
