Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, ANyone know a way to get 3 lines to appear on a 7841? The need is for a main DID and 2 other numbers to ring on the same phone in a Busy/No Answer situation. Thanks in advance! replies rated
I have Left the Voicemail to user Voicemail. But I don't see the Voicemail Count increased in the Mailbox of unity connection.The user is also not seeing the VMI ON. not sure where my voicemail messages are going..? 07:34:15, New Call, CalledId=111...
Hi, We have a ISR4331 with a NIM-2FXS where a postal meter need to me connected. The PSTN is with a PRI. The postal meter is configured to dial 9 before the numbre that must be reached. When the device place a call we get fast busy and in the debug...
Hello, I have the following setup. 1) x7815, part of a Hunt. 2) x7815 has SNR to my Mobile phone. 3) There is a Call Handler that plays a Greeting before calling the Hunt. Test: 1) from my Mobile I call in, and the Greeting is played from Unity. 2)...
Hi All, I've just been dropped in the deep end as a sysadmin for a large company, with no Cisco training beyond device profile/end user, it's both an Amazing and a Daunting place to start my Cisco Journey. Can anyone advise if it's possible to fo...
Hi Guys, I see a buggy behavior, where i can see router is generating SIP message on debug but not transmitting it on interface level. IOS version Version 15.2(4)M4 Hardware 2911/k9 Ran some debug and wireshark to confirm this. debug voip ccapi...
DX650 phones are registered to CUCM version 10.5. CUCM is integrated with LDAP for user database. User information in LDAP has both telephone number & directory URI details. Directory search works fine in all phones. But when the searched user is...
Hi all, I have some question would like to clarify and understand that can I download the device load profile for the phone model of 7811, 7821, 7841 and 7861 from this download link = https://software.cisco.com/download/home/284892537/type/282074...
I would like to know if a line is "off hook" or if the line is busy. I am the admin, and would like to reboot the 8851 phone for a variety of reasons (In this particular case to enable bluethooth). I have googled this a lot, with no info. How do I...
I am trying to register and use a Lifesize VIdeo Conferencing Codec (Icon 600) with our Callmanager phone system. I have setup a 3rd party advanced phone and extension with the Icon's MAC address and setup an extension and user for this phone. (...
All, Bit of a strange one... We have a Hunt Pilot in place with a Hunt List and Line Group, when we call the Hunt Pilot internally, calls route fine to the LG and pickup works fine. However when the call is transferred from a Unity Call Handler with ...
Anyone know if these ATA 190-SC models, with the 1 analog port can be used on Communications Manager?
Have a problem (internationally) where we forward a number to another local in-country number. However when we send outbound calls we append a + sign to them. This has caused the transfer to fail for mobile or land line users in-country because the...
Dear All, I have a quick question. Can we do call forwarding for one user who receives international call on his IP phone to other extension. Only the international call. How to do that please? Thank you
Hi there I am concern that I have a sip trunk to some avaya PBX (somewhere else), they point their SIP Trunk to the ip address of my subscriber, we had to power down my PUB, and my Sip trunk came down as well, I thought that my SIP trunk was going ...
