Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello everyone, i have a big problem with the configuration for an german SIP-Trunk.The provider ist Sipgate.de My problems are:i can call outbound but my correct number ist not shown.(correct: 0049366511397816 shown:004936651139780) i cannot recieve...
Does anyone have some examples of route patterns for dialing in Japan (for CUCM located inside Japan of course)? Or could you look at my examples and see if they're correct, assuming the person replying here has experience with CUCM installed in Jap...
Hi All, Ive recently passed the CCIE Collaboration written exam and am in the throws of setting up a small home lab consisting of some basics:2811 router +PVDMs3750 PoE switch4 x 9971 phones2 x 7940's1 x 7965 (I think its bricked)1 x 7962 (currently ...
I have some 8841 phones and the Date/Time group is set to Y-M-D. However, the year does not display. In firmware version sip88xx.11-5-1SR1-1, the year did display. In firmware version sip88xx.11-7-1-17 and sip88xx.12-0-1-8, the year does not displ...
I have calls coming in/going out from/to Avaya PBX which is connected to CUCM, All the avaya extension could reach the local PSAP when dialed 911, but when the extensions on the CUCM dial 911 they go to a different PSAP other than the one local. I ha...
Hi all, I have CUCM version 8.5 connecting to a C6500 series switch as its gateway. I have a total of 6 PRI lines in the switch with 3 PRI lines going to PSTN A and the other 3 going to PSTN B. I would like to know how to prioritise outgoing ca...
Hi Recently I upgraded several access swicthes (2960, 3650's) which have POE and Cisco 7962 phones connected. After the upgarde and subsequent reboot, the IP phones failed to power up and are effectively dead. All that happen on the phone now is tha...
I recently installed CUP 8.5.4. However after installation I am unable to login CUP Administration and Serviceability page. I can login through SSH, CUP OS Administration and CUP Disaster Recovery System.Please help me why I cannot login on Administr...
Hi, wondering if someone could help me to find out Cisco CUCM 9.X and UCCX 9.X device licenses part numbers?for example:I am looking for part numnbers belowCUWL Professional (9.x)CUWL Standard (9.x)Enhanced PlusEnhanced (9.x)Basic (9.x)Essential (9.x...
Two years ago, the platform I now manage was upgraded from V9 to 10.5. It was a secure mode super cluster consisting of 12000 CIPC phones and 7000 various hard phones. The upgrade broke the secure mode on the CIPC which would not registered and have...
Hi there, i have confugured a SX10 registered at VCS X8.1 to call a cisco 8845 registered at CUCM 11.0.1 using the appropiate cisco deployment guide. As result, the video phone can call to SX10 and the video call is established, but the SX10 can´t ca...
We have a site with a 4351 H323 Voice Gateway. After a power outage last day, both incoming and outgoing calls are not working. After deleting and reconfiguring the controller, i am seeing the below errors on the console. T1 controller and ISDN statu...
I am lazy and HATE dialing a 1 within the USA. So I have a translation to add the 1 for me and my 10 digit dialing works fine.The problem is that the caller-id shows the 4 digit extion and not my main number. What do I need to do to change the exten...
Hi, If a person is on the phone, the caller should get a busy tone or a call wait tone.Right now he gets a ring tone.Is there any way i can get a busy or call wait tone.regardsNeo
I'm trying to set up one of our receptionist lines to roll over to another line if the receptionist doesnt answer. I beleive I have things configured correctly, but it doesnt appear to work. Here is a screen shot from within Call Manager. ...
