Activity in Technology and Support
Resolved! FTD Routing question
Hi to all,i am facing the following problem, please refer also to the png attached (i also have some information on the png attached).An IPsec VPN 2811 router tries to establish an IPSec vpn with an FTD. I have setup this config on the lab and i noti...
Mobility traffic ports
[Edited on March 16th to add details]HelloI was a bit confused about the traffic ports used by mobility on WLC AireOS or IOS-XE.Trying a quick review of traffic ports used by mobility :AireOS IRCM other than 8.5 IRCM or 8.8.111 and latersince this do...
Laptop can't pair with smart TV both are connected with different SSID
Dear Concern,I'm facing an issue where when I connect my laptop to a smart LED, it doesn't connect via WIFI. My laptop is connected to a different SSID, and the LED is connected to a different SSID, but both can ping each other's because of SVIs conf...
Allowing access through ISR-C1111 to FPR1010
HelloSo I configured my RA configuration on my FPR1010 for access to my LAN 192.168.5.0/24 but was curious how exactly would I allow this on my ISR to let me connect to it? Not exactly sure which Ports would be needed opened
A9K-8HG-FLEX-TR not booting with A9K-RSP880-LT-TR running IOS XR 7.9.3
We are trying to set-up A9K-8HG-FLEX-TR in the ASR-9906 chassis with redundant A9K-RSP880-LT-TR and running IOS XR 7.9.3, but after about 2 hours the module is still in the SW_INACTIVE state. All the lights on the module are amber color, but it does...
Unable to factory reset cisco 9300L switch to default settings.
Hello All,We are unable to reset our switch to the factory settings. Its a new switch out off the box that we configured (attempted to configure) and hosed it up. The factory default password isn't working user ID cisco and PW using the system SN. ...
problem VRRP, LACP Nexus 3048TP LAN1K9
Hi, i have problem of synced betewin my 2 switchs nexus 7.0.3.i7.3I use feature BGP, LACP and VRRP (also VPC etc..)But it's impossible of configure correctly the protocolI have many errors :One : In log :%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 9-1...
Catalyst 9100 Access Points not able to communicate with Cisco Aironet
As of now, we are using WLC and Access Points as per the following make and model:Cisco Aironet 1815i Access PointModel: AIR-AP1815I-D-K9Software Version: 8.10.185.0Now, we have purchased new Catalyst 9100 Access Points:AP Model number: C9105AXI-DAft...
IPsec tunnel using private ip
Hi All, Can we create an ipsec tunnel between umbrella data center and Cisco FTD firewall using private ip ?. In my infrastructure isp is terminated on router and FTD is behind Router.
WLC - mDNS Bridging Between Wired LANs
Does a WLC support bridging mDNS between wired LANs only? More accurately, will it respond with mDNS service provider info learnt from wired LANs to mDNS queries coming from wired devices in other LANs? I had assumed so, but debugging today I'm seein...
Resolved! Creating a S2S VPN - protected networks via IP extended ACL
Hi to all,i was trying to find why the the vpn between an FTD and a cisco router could not come up and concluded to this:When i create the S2S VPN PtP topology if i just add the protected networks, the tunnel does not come up.For example if behind th...
Secondary WLC over the internet for APs operating on Local Mode
Dear Gents, What are the recommendations that should be followed if we have a local site with wireless APs operating in Local Mode and registering on a local Primary WLC on the same network. and in the case of Primary WLC failure, the APs w...
vManage unable to talk to devices after poweron
I'm running vManage 20.9.4.1 in EVE-NG, and every time I power-on my virtual topology, the vManage doesn't work after it boots.DTLS tunnels do form from vManage to the vSmart/vBond and Edge Routers, but vManage can't actually send any commands to the...
CCW needed or not In case of license renew of cisco ironport (ESA)
Hi,If we want to renew license of cisco ESA, CCW needed or not?
Resolved! Pinging through ASA from Outside
Hi everyone,I have this basic scenario:(LAN) --------- (ASA) ---------- (DSL Router) ---------- (Internet)I am able to ping the DSL Router from the LAN but not vice versa. Is it a common case with the ASA deployed in between or am I missing something...
| User | Helpful Count |
|---|---|
| 145 | |
| 128 | |
| 102 | |
| 96 | |
| 69 |
