Activity in Technology and Support
DYNAMIC ROUTING WITH ZERO LOOPS
Hello Team,I have a topology as below;I have point to point connections to multiple partners who have different unique prefixes - to avoid overlapping of subnets.They need to access my internal resources - in this case vlan 50 and 70 for respective s...
GRE Tunnel streams
This is very high level, wanting to know if this is possible. We're the middle man. I don't have access to or knowledge of equipment or configs on the other providers. Currently we are handed off a GRE tunnel to a router. We have an ipsec tunnel ...
ISE-PIC Implementation - License Type
I am looking to implement ISE-PIC for 500 users. Will the standard license up to 3000 sessions (R-ISE-PIC-VM-K9) be satisfactory? I am not sure if users ever create more than one session? Thank you. Charles.
NTP Server Unreachable post upgrade CUCM 15 SU1
Hi Everyone I have some issues after upgrading from CUCM version 12.5 to 15 SU1, the NTP appears warning as unreachable. I tried to check the status in the cli, but the status is stopped but if I try to start the service the status service is runnin...
PC can ping router but cannot ping a different network (Packet Tracer)
Hello,I am doing a lab for class that's due at midnight tonight and I've been having trouble for the past couple of days. The assignment is to essentially create a topology with 4 different networks connected with 3 different routers. 3 of the networ...
Resolved! UC Version 15 Post Upgrade NTP Issue
Has anyone had any issues with NTP after upgrading to version 15? I just upgraded my test CER cluster from v14su3 to v15su1. I had an issue with the database not starting on the primary node after switching versions. But a reboot of the server fixed ...
WxCC Agent State Visualization
Quick question on creating a simple Visualization to display agent state and idle code name. I've crated the report and have it embedded into the agent desktop fine, but I can't figure out how to get around adding a 'profile variable' into the visua...
Resolved! Access to services cisco
Hi! i dont have acces to services.cisco.com, I need help.
IPsec over NAT444 issue
Hello Everyone I have to set up an ipsec tunnel with Lo0 as source of tha tunnel. Nat is activated in My CE and in the ISP level (NAT444)All ipsec and Nat configuration is ok but, and as I know that for the NAT to work correctly, the packet should pa...
Firepower 1120 stuck in boot and factory reset
Hi.We have an 1120 that just blinks green in the status LED.So I've connected to the CLI via USB and can see it stops at "Creating FXOS swap file..." when booting from itself. But also if I try to boot with a new image on a USB.When I try to factory ...
Resolved! Issue with intervaln routing with our CBS 350 switches.
This is related to a previous issue I posted here "titled issue-getting reply traffic back from our cbs 350 switches".I have three VLANs defined on our CBS350 switches and sub-interfaces configured on our router (PaloAlto firewall) with all policies ...
Resolved! FTD wildcard cert showing CA not available
I have imported the PKCS12 file into objects > PKI > Cert enrollmentWhen adding the cert to the device it is stating CA not available.. is this because the CA Root and Sub CA's are also required to be added to the PKI cert enrollment section?This par...
Protocol error trying to create a huawei NED with NETCONF NED builder
I am trying to create a NED with NETCONF NED builder for Huawei vrp devices (i.e. NE40E-XA series). I have a device and I have done the onboarding in NSO as it is specified in the documentation:devices device huaweinetconfaddress x.x.x.xport 22authgr...
Resolved! Issue port-forwarding on Cisco ASA
Hello!We have a Cisco ASA running version 9.18.4.22 that we are trying to do port forwarding on. Right now an endpoint hits the outside interface ip and should forward the traffic to one of our servers that sits on the inside interface. I had set thi...
Cisco ASR 1001-X IPv6 issues with ACL's and encapsulation failed
hi guysI'm having an issue tuning my IPv6 outbound flows on the ASR1001-X (1Gen) and my struggle is that MTR is now showing the IP address of the router itself or showing the packet loss on the level of 90%. All other hops are fine and at the end my ...
| User | Helpful Count |
|---|---|
| 161 | |
| 138 | |
| 104 | |
| 81 | |
| 72 |
