Activity in Technology and Support
Catalyst Center VA 2.3.7.4 install failing
Trying to install Catalyst Center Virtual Appliance ver 2.3.7.4 to an ESXi 7 host. After the VM is created, I can go through the install and configuration steps without issue. However, after logging into the GUI, I'm greeted with a blank home scree...
multicast VRF through global routing table
hi team,I have c9300 connected to SRX 340 via static route. I have also VRF on this switch with vrf default route through global. the VRF has source multicast and needs to get out through global routing table. VRF config po11no switchportip vrf for...
Cisco Packet Tracer - Firewall vs Router: intra-interface Routing
Hello, Everyone.I am currently trying to setup 2 networks, 192.168.1.0 and 192.168.2.0, so that they can ping each other(and eventually talk to each other). However they are to communicate with each other using firewalls, specifically the ASA 5506-X....
IOS XE EVPN IRB multihoming failover traffic loss
set up a IRB anycast gateway in two PEs for multihoming for one CE according to below guide. https://www.cisco.com/c/en/us/td/docs/routers/ios/config/17-x/mpls/b-mpls/m-evpn-over-mpls.html somehow it worked as expected until one PE failed and the CE ...
DUMP from remote equipment
Hello everyone how to take dump from remote equipment.link just for older cisco router for-example 1900 etc, i have router asr1001 eps doesn't workinghttps://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-embedded-packet-capture/116045-pro...
Resolved! Enabling application visibility in Flexible Netflow packets via NBAR
Hello guys I'm having a little trouble with NBAR and I'm hoping someone could be of help. So I've just deployed SolarWinds and I'm trying to enable NBAR on Cisco C9404R switch for deep application visibility. Then have the NBAR data applied into Netf...
Resolved! cannot change cisco 3850 switch number
This switch was part of a stackwise group and I am trying to change from switch 7 to switch 1. I am using this:Switch Ports Model SW Version SW Image Mode------ ----- ----- ---------- ---------- ----* 7 56 WS-C3850-48P 16.12.12 CAT3K_CAA-UNIVERSALK9 ...
Resolved! Finesse om_calltype
We're creating a Finesse gadget that will do the work of a Workflow due to Workflows limitations of being only able to send five variables. With the gadget, we're able to send the variables that we want. One thing I noticed in the Finesse logs within...
Resolved! IW-6300H-AC-I-K9 with two antenna
Dears, We have IW-6300H-AC-I-K9 AP, and we need to connect two antenna AIR-ANT2588P3M-N= to it And I need to know the possibility of doing this: Please note that according to the link https://www.cisco.com/c/en/us/td/docs/wireless/outdo...
Termination failed - Cisco Modeling Labs
Hi,I am not able to terminate this lab: Cisco Modeling Labs-20251025T19180562Have tried different suggested solution on this forum but nothing has helped. The lab has been in "Terminating" state for a week or so.Any ideas on how to solve this?
CH Greeting
In CUC v14 or v15, I cannot locate where I can limit the number of times a System Call Handler Greeting will play? Mine keeps repeating. I do not see anything in ‘After Greeting’, to Prompt, Repeat, or limit the number of Times to Play. Was the loc...
Disabling SNMP traps for access ports linkdown/linkup events
Hi all,One of my clients wants to disable SNMP traps for access ports linkup and linkdown (F0532) events. I tried by "unselecting" Access Port (eqpt.LeafP) under SNMP tab of the monitoring policy is applied to the policy group of the leaf access por...
c9500-48y4c CPLD version mismatch
I have 2 C9500-48Y4C switches.Before I deploy them I want to make sure that everything is current and matching.When I do show version on one of them, I get this:Motherboard Assembly Number : 4873Model Revision Number : V02Motherboard Revision Number ...
Nexus 9 ethanalyzer for data plane traffic
Hello community, It's my understanding that tcpdump and ethanalyzer only capture at the control plane natively. Judging by my use of them not capturing anything otherwise, this does seem to be true. I need to do some ICMP captures on interfaces so i...
Add SIP Horn to CUCM 14
Good day team/collegues!My client interesting in connecting sip horns to CUCMPlanning to buy Hikvision DS-QAZ1307G1T-EWhile surfing google, found manuals that Algo 8186 SIP Horn speaker Device in fully compatible, but not accessable to buy here.Looki...
| User | Helpful Count |
|---|---|
| 93 | |
| 60 | |
| 55 | |
| 54 | |
| 48 |
