I am using a CUCM version 11 and I configured the LDAP User Search Base to point to a security group in LDAP Directory. The thing is that I can´t see the end users that belongs to that security group... the sync is completed but not correct. I teste...
Forum Posts
Resolved! Problem noisy call on BRI
Hello all,I hope you are doing well , I need your help. i have configured a gateway ISR 4321 , with interface BRI , the problem when a make a call i hear a noise on a call .i tested this line BRI in another gateway it work fine .I share with you in a...
I am connected to Devnet Sandbox using Cisco AnyConnect Client . CIPC version is 8.6.2- CIPC error says UnProvisioned. However , the CIPC is properly configured with DN : 5000. Would someone please help me out. I am in IST time zone.The cluster is in...
Hi there, I'm using the Jabra Evolve 75 headset which supports dual Bluetooth®-Connectivity with 2 devices (PC/Smartphone) for parallel (either/or) use of softphone (Jabber) and audio (Spotify). The headset works fine with Jabber/Webex via its own US...
Hi experts I have recently purchased some Plantronics CS 540 headsets, with the APC 42 cable. I can make/control calls, but they drop usually after less than a minute of connect time. Battery is charged, and I'm in range. The same headset works fine ...
We have CUAC advanced (12.0.5) and CUCM (11.5.1), when a call comes to the operator queue, caller hears ring back but we would like to add an announcement and MOH while they are waiting for their call to be answered. Can this be done? Using CCX or CU...
Hello,does anyone have any information as to what this error mean ?MuteConversationAudioFailures CJ:2100:16Jabber runs in V12.7.0 Kind regardsMarc
Hi, I want to know what exactly the cop file is? 1. Before upgrading UCCX or CUCM from one version to another version need to install cop file, but why 2. Without cop file its possible to upgrade the UC Version. If yes, then why we required this. 3...
Hi Everyone,I want to know if it is possible to activate the service "activation codeé on a CUCM in release 11.5.(1) SU4 in order to be able to onboard my client's video devices on the webex cloud (via the webex device connector application) while ke...
Just did a fresh install of 10.5.2 and upgraded to SU2a. I'm able to add a SFTP server for backups, but when I go to either backup the Publisher or try to run a restore of a backup that was taken from a previous install I'm getting this: Unable to p...
Hello all, I would like to install My E1 ,on cisco ISR 4321 , but it not work , it give me the message error: ISR4321-1(config-controller)#pri-group timeslots 1-31E1 0/1/0: No voice port or DSP resource for voice featureE1 0/1/0: For MFT T1E1 modules...
Resolved! 4331 voice gateway with DSP problems
Hi,We have a 4331 router/voice gateway, running IOS XE Software, Version 16.09.05 with a call manager 11.5.The router has a single PRI andNAME: "subslot 0/1 db module 0", DESCR: "PVDM4-32 Voice DSP Module"PID: PVDM4-32 , VID: V02 ,to carry voice call...
Hi Everyone, We're planning on changing the default Service Parameter in our Environment for "Local route group for redirected calls". Based on what I've researched so far, this is classified as a Clusterwide parameter. We have a couple quick questi...
Greetings, Recently we migrated our CUCM from 11.5 to 12.5 (System version: 12.5.1.13900-152) registered with SLM but still, the options for ELM and self-care are visible under the disaster recovery though we can uncheck both options and schedule the...
Hi all, I am trying to install CIPC 8.6.2 to a user's computer. I already tried the workaround of deleting the Communicator folder in the User folder and deleting the registry. I attached the error we get after opening CIPC and this is after a fres...
