Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have one router cisco 43331 ISR router to be configured for Voicde SIP ling from PSTN. when i tried to put voice cammand , its not supporting any command for voice service., I m thinking this may be licence isuue. because uck9 not active, can anyb...
Can any body help us to configure KSA MOBILY SIP TRUNK CONFIGURATION FOR CISCO 3800 ROUTER to communicate with cucm
Hi,I have below setup.ISP PRI >> Cisco Voice Router >> CUCM >> FreePBX.All my did are on Cisco voice router and cucm is connected to voice router via h323. my cucm is using 4 digit dialing. All calls to the pstn are passed by cucm to voice router and...
Hello, I would like some help from you!I have a CISCO 2921 SIP router and I'm having problems receiving calls, but I'm able to make calls normally, I checked other community posts and saw a lot about MGCP, but on my router it's disabled.It's not a pr...
Hey Community, So, I configured SRST fallback on my 8200L router, which I will be using as a voice gateway for my site, but whenever I try the fallback mechanism, it doesn't work and the IP phone stays stuck on verify your network connection. I have ...
Hi All, Has the command "session server-group XX" been superseded by something else? The only options I get from the dial-peer are protocol, target or transport. Cannot find anything. This is an ISR 4321 Thanks Paul
Hello,We are having an issue where if a caller blocks their caller ID the inbound call is not routed. I have tested it myself by using *67 and dialing into my desk. I get a few seconds of silence then the call drops. The calling party name is ano...
Hello, I been trying to add 7811 phones to CME 14 on a 4321 ISR router. Tried using the usual ephone-dn and ephone (#) way, but 7811 doesnt show up as a type . creating voice register pool with 7811 gives error. Found this in some of the forum entri...
HiI suddenly started facing a problem. When call forwarding is applied on an extension and it is called from external number then i do get call forwarded on external number but it adds +51 to the number.suppose I have Ext 7225 (externally its reachab...
Hello,I have ISDN PRI trunks for PSTN calls and use a Cisco CUBE as voice gateway. CUBE to CUCM has SIP trunk in between. In CUCM, we route the calls based on Calling Number. The purpose is to block spam calls in CUCM using translation patterns.Howev...
Hi everybody. We have a ISR 4321 Voice gateway registered in webex calling as a local gateway. I would like to know, if is it possible to configure this device as a local gateway and survivability and this device works as a local gateway and survivab...
I am converting phones from a ROLM 9751 PBX over to a Cisco UC solution. I have one GAI-tronics analog "Intrinsically-Safe" (IS) 262-001 phone with a 263-000 Isolation Barrier Unit (IBU) between the phone and PBX (or analog VGW). On the ROLM PBX, the...
Dear Our topology as below PSTN ------PRI E1---Cisco Router 4331 SIP GW----CUCM 11.5 ---Cisco SIP IP Phonewe need to record all outbound calls from Cisco SIP IP Phone through PSTN PRI, our customer asked for network-based recording option.My question...
Good day to all of you. 10/10/2023 11:10 PM • Im trying to register a local gateway with Webex but it is not able to get through.Webex hub has been configured as per the help.webex.com document and other guides provided by Cisco. The credentials gen...
iam configuring Cisco Voice gateway ISR 4321 for Webex calling. but i am not able to enter the following command in sip-ua and it is showing crypto as unrecognized command . Please help me to resolve this issue. sip-ua crypto signaling default trustp...
