Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Publisher CM works fine, but when the Subscriber takes over there is no access to outside lines from the 2921 Voice Router. The Subscriber CM is syncing with the Publisher CM OK. CM 8.5 2921 Voice Router at site. 2 PRI Lines, plus 5 pots lines in th...
Hi Guys, We have installed few phones in a new branch site. Phones are missing functionality like pickup, cfwoff, Fac code and firmware is not upgrading. CM 11.5 VG srst 2901 Please advise the troubleshooting . Thanks
Hi There I hope you are well. I have a CUCM 8.6 PBX as my main PBX with about 10 PRI's. I have setup a SIP trunk between it and a FreePBX VM for IVR functionality. I have managed to get all this to work, but now I would like to get the extensions I...
I had the issue with "Unable to change tftp address in IP Communicator 8.6.1.0" 1> I tried selecting 'run as administrator' didn't appear to work for me at first. Turns out I wasn't closing the application all the way before trying to run it again a...
Hi, How can I forward all incoming calls from either an external or internal number to an external number only on certain schedule. I want to forward all the incoming calls to my extension just if they are from 9pm to 9am or weekend. I tried with a ...
Dears i upgrade the unity connection from 9.1 su2 to su5 and it was successful i switched version on publisher after the publisher came up successfully i took longer time to to switch version on subscriber and then it give me the below error on subs...
I am running a couple of rear monitors off the output 3 connection on a MX800 Dual. I've read through the guides and it looks like I am able to add a panel to the Touch 10 that would allow for swapping of the monitor roles on those monitors but I hav...
Hello Everyone, My name is George. I work for a local IT comapny and I have been tasked with working with our 7940G phone system. I am totally out of my depth with this and I don't have the slightest idea where to start. As expected my supervisor...
Hello,I have a problem configuring the IP Phones, I register the post, in CUCM, and when I plug the IP Phone into the Switch, the station does not recover its network configuration, I give you the elements of my Lab: CUCM 11.5, Cisco ROuter 2901, Cat...
when reset ,it was normal,but after mute lights,it did not reset , display "big easy diagnostics" after cisco logo. and whatever I reset ,it display the same. someone know about this?
This is Unity Connection running 10.5. I have received the alert On Sun Feb 28 20:47:53 EST 2016, alert LowSwapPartitionAvailableDiskSpace has occured. Counter Percent Available of Partition(Swap) on node X.X.X.X has value of 9 which is under low th...
Usually the SWAP Partition is being used when the RAM on server is being exhausted completely and we use SWAP partition to carry out the functions. We cannot free up the SWAP partition when the Call Manager / Cisco Unity / Cisco Unity connection / ...
Want to create daily reports about some phone devices First: Did this as follows: Cisco Unified Serviceability Tools / CDR Analysis and Reporting User Reports / Top N / By Number of Calls - Report Type 'By extensions' - No of Records 5000 - Report F...
In Cisco IP Phone 6945 how to modify second line Softkey template ( We have 4 Line button). i have applied customize softkey template but it is taking affect on line 1 and not in line 2. Any idea how to change.
Hi Team My customer will implement EMCC on CUCM clusters soon. I have a question about the EMCC with recording feature. Assumption: EMCC is enable on all CUCM cluster.1. User A (with EM profile A) login the phone A (with BIB feature) in CUCM A. One J...
