IP Telephony and Phones

Softkeys change with second incoming call

CUCM 11, 7965 phones. While on a call, softkeys display the CONNECTED options from the SoftKey template. However, when a new call comes in (second call), the SoftKeys change to the ringing softkeys. Is there a way to prevent that? I want to keep t...

CUCM --- CUCM - One Way Calling Issue

I have a Lab Setup with One CUCM Pub on one side of a SSL VPN and another CUCM Pub on the other side. I am succesfully able to call over both ICT / SIP trunk from one side to the other, but when calling from the other side back I get a fast busy. Cur...

Cisco Phones hears ringback even after the mobile person disconnect

Hi am using CUCM 10 and h323 gateway 3 PRI . I found that when i dial to mobile phone and just disconnect the call from the mobile , still the cisco phone rings . I informed that service provider is not sending the RX disconnect (disconnect signal )...

Resolved! Transfer Calls

Hello,I have CME , some sccp phone ,and one sip phone 7821. I can call from SIP to SCCP and vice versa as well. but the issue is if someone called in and SCCP answer the call, it then cannot transfer to SIP user.regards

CUBE dial peer vs routtern pattern UCM

Hello Friends,Topology: UCM>Trunk>MGCP>SRST CUBE GW>SIP Trunk> ITSP. I wanted to discuss about dial plan on SIP Trunk CUBE GW and UCM server using MGCP as control protocol.I understand you set up all routtern patterns on UCM under MGCP protocol, so y...

Resolved! Connected Party Name Pass Through via PAI on CUBE

I have a CUBE setup between Cisco CUCM (v9.1) and an Avaya PBX to allow extension dialling between both systems. Calls are established ok, however the connected party information is not being passed from CUCM to the Avaya by the CUBE. CUCM sends the ...

Resolved! Phone's firmware in CUCM image.

Hello,I'd like to know the phone's firmware versions loaded in the cucm 10.5 (or how to know).We want to upgrade to UCM 10.5 and we have defined a pre-tasks. One of these pre-tasks is upgrade the phone's firmware with the same version loaded in UCM 1...

DX650 issues with Visual Voicemail and Directory Photos

I am having a couple issues with getting a couple things working on the DX650 and was wondering if anyone had the same issues and fixed them.1. Visual Voicemail: I've set everything up per Cisco's instructions here http://www.cisco.com/c/en/us/td/do...

7925 Audio delay when answering calls

We’re having a Cisco Wireless 7925 Audio delay issue. When calls are answered the first 5 to 16 seconds there is not audio available. The issue is sporadic and not easily replicated which makes it very difficult to capture traces. It appears that the...

Cisco Call Manager Not Booting

Hello all,I have a Cisco Unified CM 6.1.2 running on CISCO MCS7800. Now it is not booting up. Unable to get login page.I am getting error as shown in the snapshot.Can somebody guide on what to do for recovery.RegardsArun Sai

Resolved! outbound ports to allow for SIP ?

Hello, my VoiP phones are on the LAN and I was only allowing certain OUTBOUND ports through my firewall i.e HTTP, FTP, SMTP, POP, DNS, SIP 5060 etc.I found I was only getting one way audio. As soon as I allowed 'ANY' OUTBOUND port through my firewall...

Resolved! How to open CDR file

I added a CDR SFTP server on servicibility page... CUCM has started pushing files to this server..But how do i open these files?file name look like "cdr_CUCMCluster_02_201509280355_440782"there is no extension.I use a windows.

Associate users to phones

Please , I have to implemente BE6000 in a small copany, I want to associate a user to ip phone 7861, I have already created users , and phones bay using BAT. I am stack in how to attach a phone to each user, and how user can log in the phone ?? Does ...

Resolved! About CCM Route Pattern number exclude

Hi FriendsI have a question about Route Pattern number exclude.Now 9.222XXXXXX is to my city 9.[^2][^2][^2] XXXXXX is to other citybut if i dial 9233666666 , I can not make the callso i try 9.[^222]XXXXXX, I still can not make the call But I...

#DEVICENAME# Parameter - Other Parameters?

I know how to pass the MAC of a phone using: http://hostname.tld/?name=#DEVICENAME#I want to know how to pass the user locale for a subscribed IP Phone Service.Does anyone know what other parameters are available for use? Where is this information d...

IP Telephony and Phones

Forum Posts

Softkeys change with second incoming call

CUCM --- CUCM - One Way Calling Issue

Cisco Phones hears ringback even after the mobile person disconnect

Resolved! Transfer Calls

CUBE dial peer vs routtern pattern UCM

Resolved! Connected Party Name Pass Through via PAI on CUBE

Resolved! Phone's firmware in CUCM image.

DX650 issues with Visual Voicemail and Directory Photos

7925 Audio delay when answering calls

Cisco Call Manager Not Booting

Resolved! outbound ports to allow for SIP ?

Resolved! How to open CDR file

Associate users to phones

Resolved! About CCM Route Pattern number exclude

#DEVICENAME# Parameter - Other Parameters?

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Incoming calls show as forwarded

CUCM sends wrong device ID to Recording System

CDR reports: Request for activity on multiple lines

I get dozens of these alarms on WU, but no errros on controller

Transfer Caller ID and 8800 Line Buttons CME

CUCM 14 LDAPS certicate issue

SIP Trunk STC

4331-Vk/9 router replacement can it be C8200L-1N-4T

CUCM 14 "Operation Completes by" Problem with 2023

Call forwarding not working ( Vodafone Germany)